Find professional sliding gate repairs near you

Need help with the assembly and installation of the slat fencing, entrance gate, colorbond side fence instalation(approx 2.8m each side for the colorbond), we have all the materials from Stratco. Please send me your quote.

I need a remote for my gate programmed to open and close it

I need my remote programmed to my sliding front gate

Have a new remote but can’t program it to automatic gate. Or program it to housemates remote that works

I had to get a new remote for gate but can not program it to gate. I have house parters remote

Looking for an experienced handyman/carpenter to relocate an existing sliding timber gate/barrier on a warehouse mezzanine. This is mainly a relocation job — the gate and timber materials are already available. Scope of work: * Remove the existing sliding gate from its current position * Relocate and install the gate in another opening on the same mezzanine * New opening is approximately 2.34 m wide * Reinstall/modify the existing sliding track, brackets and hardware as required * Make sure the gate slides properly and can be securely closed/locked * Close the old gate opening using the existing horizontal timber rails * Timber pieces are already cut to size and ready for installation * Secure all timber properly to the existing structure * Leave the area clean after completion Photos attached show: 1. Existing sliding gate and track 2. New 2.34 m opening where the gate needs to be installed 3. Timber already available to close the old opening Location: Burleigh Heads, QLD 4220 Please include labour and any minor fixings/hardware required in your offer. Important: This is on a warehouse mezzanine, so please only make an offer if you have the appropriate tools and are comfortable working in this type of environment.

Supply and install fencing, please provide reference pictures for your quote. Information as follows 15m total, minimum 1.5m height, to include sliding gate and pedestrian gate. Located in Moorabbin 3189

Installation of an outdoor power point for automatic sliding gate next to concrete slab for motor and track which has yet to be poured. I am replacing the driveway so I can get the concreter to run a conduit in preparation for cabling so no trenching is required.

Brick wall and sliding gate on the side of the house. All about 4 m long area. I think the gate would be about 1.5 m long.

I have a 4m x 1.5m slat gate I need installed. I have all hardware on hand, and also have concrete pad installed ready. Need hole dug for guide post (the one item I don’t have)

Already installed Ahouse motor. But giving error E3.

After somebody with some experience in making the electric VEVOR gate motor open and close at my house, as photos indicate the motor is mounted and powered up, but I’m having trouble linking the remotes/keypad etc and the magnets which shut off the motor.

Description: Seeking an experienced gate installer/repairer or gate automation technician for three tasks at a residential property in Chatswood NSW: 1. Adjust two aluminium swing pedestrian gates Two blade-style aluminium swing gates (side access and front entry) are not closing/latching properly. Adjust hinges, alignment and latch/lock strike so both gates self-close and latch cleanly. Photos attached show the gates and latch hardware. 2. Rewire/connect sliding driveway gate safety sensor The automated sliding driveway gate (Beninca) has a replacement photoelectric safety beam sensor that needs to be wired back to the controller and configured — the original was damaged and has been swapped but not connected. If the replacement sensor is faulty or incompatible, supply and install a new photobeam pair instead (quote parts separately). 3. Test driveway gate operation Full function test: open/close cycles, obstruction detection/auto-reverse via the beam, limit settings, and remote operation. Requirements: Experience with automated sliding gates and gate motor controllers essential Bring standard tools; power available on site Please review attached photos/video before quoting Advise if parts (photobeam sensor) will be extra and estimated cost Location: Chatswood NSW 2067

Sliding gate motor is working but very slow. We think the bearers inside are worn? Requires assessment and repair. Job location: Maidstone

Task Description Paint timber‑clad sliding gate on a powder coated metal frame Approximately 5m (L) × 1.6m (H). Includes full surface preparation and application of two coats (Front and Back) Paint will be supplied. Must be an experienced painter with strong, long term references. Applicants with limited experience, few reviews, or below‑average ratings will not be considered unfortunately

My driveway entry gate is not functioning properly and needs attention/service. It’s an automatic sliding gate powered by a Tau K100M motor. See photos. The gate will not open without manual effort as the cog on the motor will not grip on the gate frame (to pull and slide it open). It closes no problem. I have a video that shows this clearly. I’ve examined the parts and there doesn’t appear to be any wear and tear causing this. I suspect it just needs realignment now and then.

Change cylinder of front door lock and provide keys and help with fix/repair of sliding door

I need new sliding gate motor supplied and installed

Looking to get colorbond fence and electric gate supplied and installed in my front yard, also old fence removed. Pic attached for reference of measurements

Fees is for making a contact only. We fabricate sliding and swing gates. We need person who has knowledge of gate automation to work for us a subcontractor.