Find professional sliding gate repairs in QLD

Old gate motor died, have a VEVOR to be installed - Existing tracks may well be ok, new tracks available if not. Installation and programming of limits for new motor, plus remotes required. Prefer someone who has done one of these before - instructions are in Chinglish

Remote control not work. Attached photo shows the LED screen. I have attached the magic button control board.

From time to time I need installation of solar powered swing and sliding gate automation systems in the Brisbane south area. A single swing gate system can be installed in 3-4hrs once you have a bit of experience and the charge rate for that would be around $490, a double gate around $590.

Looking for a licensed electrician to connect power to a new sliding gate motor at a residential property in Riverhills. Scope of Works • Electrical installation, cable run and final connection only. Exclusions: • Sliding gate motor has already been purchased. (Brand: LEXOautomation). All gate automation equipment has already been supplied.No equipment procurement required. Cable Route: The switchboard is located on the left-hand side of the house and the driveway. The gate motor is located at the front fence near the driveway entrance, adjacent to the letterbox. Right-handed side of the driveway. Approximate route: • 2m from switchboard area • 6m along side access • 7m to gate motor location Approximate cable route is 15 - 16m. Maybe allow approximately 20m total cable length including wall rise, terminations and installation allowance. The cable will need to cross sections of existing concrete driveway. The concrete side path is about 1 meter wide. We plan to wire the cable underneath across the side path. The wall rise from ground level to the switchboard is approximately 1.6m. A site sketch showing the proposed route is available and can be provided together with photos. Please kindly provide separate pricing for: Option 1 – Homeowner excavates trench under electrician's direction; electrician supplies and installs electrical works only. Option 2 – Electrician supplies all labour including trenching and electrical works. Please also advise (if you could): • Required trench depth. • Your preferred method for crossing the concrete driveway. (Our preferred route is drawn in the photos) • Whether a dedicated circuit is required. • Any additional materials required beyond the supplied gate equipment. • Whether a Certificate of Compliance can be provided upon completion. Power is available at the existing switchboard and access to the proposed cable route is clear. Please send your quote and availability. Location: Riverhills QLD 4074

Drive fault error- centurion motor for sliding gate

Concrete strip job beside the Colorbond fence: 10 m long 450 mm wide 150 mm thick reinforced concrete Please use the existing concrete level near the Colorbond fence as the finished height reference. Scope: Remove old concrete where required Excavate and prepare base Compact ground properly Install boxing/formwork straight and level Install reinforcing mesh on bar chairs Pour and finish concrete level and smooth Important:The strip must be perfectly straight and level as it will be used for a future sliding gate track. Please leave site clean after completion.

Hi, I’m looking for an experienced sliding gate installer for a job in Worongary, Gold Coast. It is a 5m+ sliding gate. Materials are already supplied, installation only. Must have own tools and experience with sliding gates. Please PM me your availability, previous gate installation photos, and rough pricing. Ongoing work may be available for the right installer.

Concrete pad for electric gate

1. The motor itself is good; it runs normally and physically drives the gate. 2. When attempting to reprogram the travel limits (with DIP switch 1 set to ON), the gate cannot recognize the end points. In both the opening and closing directions, even after the gate has fully traveled and hit the physical end stoppers, the motor continues to drive hard and does not stop. 3. When observing the control board, the "REV" LED indicator stays solidly ON (constant illumination) while the motor is running, instead of flashing.

I have a 8 foot sliding gate that fell off during the storms. The 3 rollers on the bottom and the guider on top broke. I need someone to replace rollers and guider on top of gate, put gate back on track. I maybe need someone to look at this first as there may be more damage then I think there is. Gate is 8 foot and heavy. Motor is fine. Maybe need more concrete for poles and another guider pole in centre of driveway for reinforcement? Located Beenleigh. $50 is for quote only

assist our technician with lifting the sliding gate off the track and holding it in place while it is being secured. This should take approximately 30–40 minutes. Our technician is expected to arrive between 9:00 and 9:30 am.

🔧 Electric Gate Installation – Sliding Gate (Supplied) Looking for an experienced installer to complete setup of a sliding electric gate. Gate is already on-site and partially assembled. Scope includes: • Install and secure gate track • Hang and align gate for smooth operation • Install and position motor • Fit rack and ensure correct engagement • Set up stops and safety alignment • Test and calibrate for full operation Notes: • Gate and components supplied • Power will be connected by electrician (no electrical work required) • Must have experience with automatic/sliding gates - provide pictures of possible. Location: Eumundi Budget: $900

I have had a sliding made 6.4m, Need motor and slider fitted, need a post welded to an existing post which will hold slider. Motor to be installed is a Ditec ( plug and go) You must be able to connect the wiring already pre installed into the main box too. I have a circuit breaker already. All materials supplied except welding gear , just require skill and knowledge. Happy to assist. Thinking $250

Change to PVC fence and pvc sliding gate

Sliding gate not working. Tried two remote. Trouble shooting required. Also a third key-fob will need to be paired.

It’s a two person job to move the gate and lay it down. So I need another person. Once it’s laid down I can attach new wheels to the gate. Then we replace the gate on the runners. Probably less than 2 hours. You need to be reasonably strong as the gate is heavy and a bit awkward to move.

I need new sliding gate motor supplied and installed

Looking to get colorbond fence and electric gate supplied and installed in my front yard, also old fence removed. Pic attached for reference of measurements

Remove the sliding aluminium gate and fence including posts. Total width is 14m I will keep the gate and fence panels for future installation. Electrician will disconnect power from the sliding gate separately.

Disconnect and remove power and motor of my sliding gate.