Find professional sliding gate repairs in Inner South Melbourne

Hi, I'm looking for someone to repair an electric sliding gate as soon as possible, ideally today.While reversing the car, we accidentally bumped the gate, and since then one of the wheels appears to be out of alignment, so the gate no longer opens or closes properly. I'm looking for someone experienced with automatic sliding gates who can inspect the gate, realign or repair it if possible.

Supply and install fencing, please provide reference pictures for your quote. Information as follows 15m total, minimum 1.5m height, to include sliding gate and pedestrian gate. Located in Moorabbin 3189

I need assistance to program two remotes for a FAAC sliding gate motor. I have one existing remote that works, but need another two (which I have purchased) to be paired.

I have a sliding gate that was badly damaged by car driving into it. The steel frame needs to be repaired or replaced. Please see photos attached to get a feel for the issue (I've removed the timber from the frame). The frame is 4300x1560 constructed from 40x40 steel tube with a 40x40 rail added to the top tube. 3x wheels on the bottom. I'm in McKinnon.

Looking for a handyman, concreter, or landscaper to complete a small concrete beautifying job around three steel posts supporting an outdoor sliding gate. Scope of work: Prepare and tidy the area around each post. Form and pour small rectangular concrete patches around 3 gate posts. Finish the concrete neatly and level with the surrounding surface. Clean up the work area on completion. This is a relatively small job, to reiterate no structural work, just to finish the area around posts. I have attached 4 photos: Photos 1-3 show the three gate posts requiring finishing at base. Photo 4 shows the desired finish and approximate appearance I am aiming for. Preference is for a dark grey concrete finish if achievable. Materials and tools to be supplied by the successful Airtasker.

Task Description Paint timber‑clad sliding gate on a powder coated metal frame Approximately 5m (L) × 1.6m (H). Includes full surface preparation and application of two coats (Front and Back) Paint will be supplied. Must be an experienced painter with strong, long term references. Applicants with limited experience, few reviews, or below‑average ratings will not be considered unfortunately

I need installation of a front gate at my house. I will source material Myself whatever you need for this installation and I will pay you labour for This task. It will Be sliding aluminium blade gate 1.5 high .with motor.

We need a professional gate installer to build and install a custom metal gate frame with track and motor. Current opening is 2.8m wide and finished fence height will be 2m. Hampton style fence. We will do our own cladding after gate is installed. We also also provide the electrical connection section for motor.

Fees is for making a contact only. We fabricate sliding and swing gates. We need person who has knowledge of gate automation to work for us a subcontractor.

Build a new tubular steel fence, 1.5m high all around. Total 30m of fencing required. This is a corner block so I will need a council REPORT AND CONSENT (REG 92) application submitted to council as I want fence to be at least 1.5m high all around. Fence shall include a remote control automatic sliding gate across the driveway and an additional manual pedestrian gate. Fence style to be Oxley Ring and Spear. Sample of fence is per the attached photo.

Money is for making phone contact , no actual work required. Looking for subcontractor who can install motor, dig tranch to take 24 low voltage wires to power point to the house. Few jobs every month. We fabricate sliding gates , swing gates etc based in oakleigh melbourne.

A new replacement motor and railings has been installed but having problems programming it and the remotes

Old motor burnt out need to replace with new supplied motor

Replace electric gate sliding motor. Please only offer if you have do this sort of job regularly and are experienced.

Repair electric sliding gate. It beeps when I press the remote but it doesn’t operate anymore.

We have just installed a new fence and sliding gate. We have a source of electricity and a concrete pad for the motor We now need the gate to be automated.

Right side motor in pic not working properly. Opening gate really slowly. Supply and install new sliding gate motors, needs to be connected directly to mains and solar removed

Looking for a 12m fence with a 3.5m to 4m sliding electric gate and a side gate to the front entrance of the house. Either looking at pvc fencing or aluminium slats.

Need a fencing/gate specialist. Want 1 treated pine post cemented into the ground to be the end post or a fence. Need a metal post cemented into the ground alongside what will be the track for a sliding gate. I have the metal post. Holes need to be dug. I can purchase the timber post before job.

I require a trench to be concreted for a sliding gate. No extra digging required. It’s 3000mm long, 250mm wide and 150mm deep. MUST BE LEVEL WITH DRIVEWAY. I want rio put down also. Thanks.