Find a professional gate installation in Doncaster

The gate attachment came loose and part of the masonry is detached. Needs to get re attached and enforced

Task: Remove Existing Side Gate & Supply and Install New Colourbond Gates Remove existing side gate then then supply and install a new black Colourbond gate system. Scope: • Remove existing gate/fence • Supply and install galvanised steel posts • Supply and Install two matching black gates, metal (colourbond or similar), either solid or vertical posts with minimal gaps • Side gate posts to be 75x75x2mm gal posts, 1.95m in height out of ground to match gate height. • Posts to be set in concrete in post hole, approx 70x80cm deep. • Gates to be hinged off posts. • One gate to have pad bolt to ground, the other gate to have a keyed handle to secure. • Gates to open inward (ie. Towards back of the block) • Approximate width of driveway: 3.5m (building to boundary fence) • Desired height: 1.95m • Ensure gates are level, secure and operate smoothly Easy access. Please include all materials, and labour costs in your quote (disposal of old gates not required). Photos attached.

Hi, looking for an experienced contractor to supply & install: Work required: * Electric sliding gate * Include motor + remote + track * Front + side fencing (brick + vertical fence mix) * Side Colourbond 1.2m-2m Approx layout: Both Side: * 2m (h) x 15m * 1.8m (h) x 10m * 1.5m(h) x 4m * Side section 4m Front : * Front boundary approx 29m total * Includes brick fence + vertical fence + entry gate + electric sliding gate * Sloped site → fence balance height * Need neat, straight visual finish * Experience with uneven ground required * Remove old wooden fence around 15m Open to: * Cost-saving materials * Practical design suggestions Please include: * Quote breakdown (gate + fence + labour) * Confirm electric gate system included * Timeline * Similar past work photos

Hey there I am hoping to replace both my exterior doors. The green door with colourbond gate and white door with colourbond door please. Including the door frames for both of them.

I am in need of someone to fix the side gate of our townhouse. It is a wooden gate with a metal frame. The hinge was welded on. The welding on one of the two hinges has broken off. The other remains intact. The lock also no longer lines up well.

I need to remove the current one and replace a new one The old one need to be taken away New 2 new red doors replace the old doors Pls refer photo 1 for details.

Fence has been replaced however it has left a gap between fence and front gate and fence and neighbours brick garage. Gaps between front gate and fence approx: 12.5cm Gaps between fence and bricks: Gap 1: approx 13cm Gap 2: approx 23cm. There is also the option to extend the fence and connect the two portions, however there is only 19cm from neighbours foundation to our concrete walkway.

Need a folding security gate like the one in the link below to block off area between the carport and small veranda (~3.5m length by ~2.2m height) in the attached photo. The security gate needs to be installed against the steel pole on the left and the brick wall on the right. Please provide quote. https://www.vevor.com.au/folding-security-gate-c_10269/vevor-single-folding-security-gate-folding-door-gate-6-1-2-h-x-7-1-2-w-fold-gate-p_010337451216

Pool fence gate is too heavy which makes the supporting metal spigots sinks and sloping downwards to the right. The gate has a closure problem because of misalignment. Please provide a resolution to fix up if you have an idea to do the job before making an offer.

Hinge partially came off, unsure if new hinge is needed. Gate needs to be re-set into place

something wrong with the track

Redo cabling to make it lower so that paving can be done over it

Concrete brick pier - 2 pillars - 1.8 m high with 300 mm deep steel rods for strong foundation to support hinged gate - 80-100kg gate

Remove and replace wooden panels on side gate (see picture) with fake wooden panels. Budget excludes costs for new fake wooden panels

1 outside gate hinge door need realignment to locking mechanism

Our daul swing gate openers are not working. They are Richmond GTR058 make.

To extend the height of the existing fence and gate ( on top of colorbond fence & wood gate) eg perhaps by adding lattice etc. I am open to other options

Looking for a reliable and experienced handyman to assemble a 5-metre fence with a small gate. All fence materials and the gate are ready on-site. Labor only – no materials needed. Job Details: • Assemble and install a 5m fence • Install a small gate • Ensure the structure is secure and level Location: Doncaster Job Type: One-time task Required Skills: Experience with fence installation, attention to detail, and proper use of tools Please bring your own tools if necessary. If you’re experienced and available, please make an offer!

Electronic gate needs a little bit of repair, may alignment

I’m looking for a skilled and reliable person to help with assembling and installing a swing gate in my carport and a few sections of fencing. Both the gate and fencing materials are ready to go – I just need someone with the tools, experience, and labor to complete the job. • Materials: All gate and fence components are provided. • Task Requirements: • Assemble and install the swing gate in the carport. • Install a few sections of the fence. • Ensure proper alignment and secure fittings.