Find experienced local carpet installers in VIC

Looking to replace the carpet in my bedroom with solid, unfinished timber floorboards. The room is approximately 8.4 m² (3.25 m × 2.59 m), excluding the built-in wardrobe. Requirements: - Flooring: Solid timber only — no engineered timber, laminate, bamboo, hybrid or vinyl. - Finish: Completely raw and unfinished, with no factory or on-site oils, sealants, varnishes or other coatings. I will apply my own oil after installation. - Installation: Preferably secret-nailed, with minimal glue and adhesives. - Removal: Remove and dispose of existing carpet and inspect the subfloor for possible mould or damage. - Subfloor: Replacement may be required. If so, I prefer solid timber boards rather than plywood or sheet products, provided they are structurally suitable. There is also a floor air vent, and ideally the built-in wardrobe will remain in place. Please let me know if you can undertake this work and provide an estimate, including potential subfloor replacement costs. I understand a site inspection may be needed for an accurate quote.

The carpet is damaged, need someone to fix it

70 cm by 10 cm strip (approximately) we have spare carpet to replace it just looking for someone to seamlessly replace the piece

Water gushed out from washing machine into the bathroom and some of it came outside and entered the carpet. Its not a lot of water and has not entered more areas

Need a handyman or flooring installer to fit a transition trim where my timber floorboards meet the carpet, at the living room and hallway junction. The ends of the floorboards are currently exposed. Looking for a graduated reducer profile (ramp style) that steps down from the timber height to the carpet, not a flat flush strip. Must be fixed securely, cut cleanly at the ends. Please quote for supply and install, or install only if you'd prefer I buy the trim. Happy to pick one up from Bunnings or a flooring supplier if you tell me the profile and size. --- I do have a few additional tasks I'll need help with (sourcing a strong enough magnet for door) but will discuss at a later point.

I need a handyman to roller the glue on the surface of the slab and lay 50cm x 50cm carpet tiles squares to a 6m x 6m concrete slab. I already have the tiles and the glue.

Need quote to supply and lay carpets in 2 sample rooms. Room1: 2.8x3.1, Room2: 3.0x3.5. To be done within the next 7 days. Floor is ready for install. Location Ardeer 3022.

Stretch carpet in 1 room.

Looking to replace the carpet in my bedroom with solid, unfinished timber floorboards. The room is approximately 8.4 m² (3.25 m × 2.59 m), excluding the built-in wardrobe. Requirements: - Flooring: Solid timber only — no engineered timber, laminate, bamboo, hybrid or vinyl. - Finish: Completely raw and unfinished, with no factory or on-site oils, sealants, varnishes or other coatings. I will apply my own oil after installation. - Installation: Preferably secret-nailed, with minimal glue and adhesives. - Removal: Remove and dispose of existing carpet and inspect the subfloor for possible mould or damage. - Subfloor: Replacement may be required. If so, I prefer solid timber boards rather than plywood or sheet products, provided they are structurally suitable. There is also a floor air vent, and ideally the built-in wardrobe will remain in place. Please let me know if you can undertake this work and provide an estimate, including potential subfloor replacement costs. I understand a site inspection may be needed for an accurate quote.

Just a minir patch fix photos attached

We had to pull up a section of carpet in two rooms. It needs to be put back in to place and pulled tight. We don’t have the tool do do it. It will be about a 10minute job. Just an entrance area and the corner of the living room. I will need this done today

I need a portion of carpet installed where a heater used to be. I have the carpet. It would be good if you have some underlay, otherwise I have some - just doesn’t match the existing underlay although that doesn’t bother me. Needs to be installed and merged with the existing carpet. 1750mm x 650mm.

There are carpet beetles by the window. I have cleaned up the area but they showed up the next day. It looks like there is an entry point by the window.

The second bottom stair carpet has some damage (naughty cats) and needs replacing. We have a piece of matching carpet but just need someone to cut old piece on the whole stair tread away and replace it with new section.

I have a stained carpet in one of the bedrooms that's needing a re-patch. Unfortunately, I don't have the offcuts, I'm not sure if you can take one from closets etc. Alternatively, I can have you source it. We can work on the price including sourcing.

I have new carpets and bedroom/ensuite doors are too long for these so need them cut and resealed at the bottom. The three doors are already loose/taken off the hinges. Getting these done is a priority. My laundry door on the other hand is too wide and long and needs hinges looked at. Door is still intact. Might be a tricky one.

We need the whole carpet replaced in 3 bedrooms (ASAP) it will need to be done Monday or over this coming weekend. We can negotiate the price once offer has been made. Must provide an invoice

The small room needs carpet replaced

I’m moving out of my rental property and need a small burnt patch 2cm x 2.5cm on the carpet professionally repaired before my end-of-lease inspection. The damaged area is quite small and the rest of the carpet is in good condition. I don’t have any spare/matching carpet available, so I’m looking for someone experienced in carpet patch repairs who can advise on the best way to match and repair the area as seamlessly as possible. If required, I’m open to using a small donor piece from a discreet area such as inside a wardrobe, provided this can be done neatly.

My dog ripped up/chewed the corner of a lose bit of carpet in my bedroom, which I need repaired if possible - I don’t have a spare section of matching carpet.