Find a fence installation professional in Melbourne Eastern Suburbs

Looking for an experienced fencing contractor or carpenter to supply and install a custom double swing gate for backyard access in Box Hill, VIC. Please refer to the attached design and site photos. Specifications: * Total opening: 3,470mm (existing fence to house wall) * Height: Approx. 1,800mm * Gate widths: Approx. 1,750mm left + 1,680mm right, subject to site measurements * Style: Traditional pointed-top timber pickets, matching my existing front fence * Frame: Galvanised steel frame with suitable bracing to prevent sagging * Posts: Preferably timber, concealed behind the gate (not visible from the front) * Hinges: Heavy-duty adjustable hinges * Lock: Outdoor mechanical keypad gate lock (supplied by me; installation required) * Hardware: Include suitable drop bolts and other necessary fittings Key Requirements: 1. Gate must extend from the existing timber fence to the house wall, NOT the carport posts. 2. Supporting posts must be concealed behind the gate to maximise usable opening width. 3. Both gates must open fully to allow large furniture and equipment through. 4. Structure must be reinforced to minimise long-term sagging. 5. Posts must be securely installed without relying solely on the existing fence or weatherboard cladding. Quotation: Please provide two prices: Option 1 – Without Painting: Complete supply and installation, including posts, frames, timber pickets, hinges, hardware and lock installation. Option 2 – With Painting: Additional cost for preparation, priming and painting to match the existing house weatherboard colour. Please confirm your proposed materials, experience with similar gates, availability and estimated installation timeframe. Site inspection welcome before finalising the quote. Location: Box Hill VIC 3128.

Repair damaged side wooden fence and replace a couple of damaged panels

Looking for an experienced carpenter, fencer, or handy person to supply, build, paint, and install a pedestrian side gate between our house wall and the boundary fence. Task Details: Dimensions: Approx. 355cm wide x 1.8 m high (matching boundary fence line; site check required). Frame & Cladding: Rigid steel frame (adjustable kit or welded box frame) clad in vertical treated pine palings/battens to eliminate sag. Finish: Painted/stained in Colorbond Monument to match fence and wall cladding. House-Side Fixing: Secured into bricks Fence-Side Fixing: Securely anchored into existing boundary fence post/framing. Ground Clearance (CRITICAL): Must be puppy-proof. Install a low-profile timber plinth across the gravel so the closed gate has <25mm clearance without dragging on stones when opening. Lock & Latch: lockable gate. Tasker to Supply: Steel gate frame (or adjustable frame kit), Treated pine palings/battens, posts/timbers, and base plinth, Colorbond Monument exterior paint/stain, Heavy-duty hinges, double-sided key-lockable gravity latch, and structural fixings What to Include in Your Offer: - Confirm your quote covers full supply of all materials, latch, painting, and labour. - Briefly explain how you plan to anchor the post on the clad wall side. - Your availability and photos of previous gate installations. images attached of current drive with farm gate to be replaced with something similar to the last image

Replace two timber fence posts

See pictures. The top fence post is broken and or on the way out. Need to have it replaced

Install 3 lines of tensioned wire on fence. Roughly 2.5m long. Fence is pictured for reference

Need to get gate for side drive- 2600W x 1800H. Need someone who can have a look and think a bit outside the square. Existing gate post- just need gate. Labour only. Unless have full solution.

I have a timber paling fence with 6 rotten rails across 4 sections that need replacing. The palings and posts look to be in reasonable condition, so this is a rail repair only, not a full fence replacement. Photos attached.

I require a double door gate installed at my father's property. The height to be approx 1.8m high x 2.3m wide. He prefers a steel frame with a material that can't be seen through, so no gaps. There is a steel post on the fence side and a timber post attached to the house. Both are in good condition for attachment of hinges. It's going to be a feature so please no cheap timber paling material.

I need a welder or metalworker to replace the two hinges on a wrought iron garden gate. This budget is for labour only. I will supply and pay for the hinges and fixings separately. Please do not include hardware costs in your offer. The gate: Single leaf, approximately 2 metres wide Open picket style, estimated 40–80kg Both the gate frame and the gate post are hollow steel square tube Street-facing front gate on a brick pier Existing hinges are old hand-made welded barrel hinges, rusted and worn Photos are attached — please look at them before making an offer. Scope of work: Support the gate, cut off the two existing welded hinges and grind the surfaces flush Weld the gate-side half of each new hinge to the gate frame. Tack weld and check alignment first, then complete the welds using a staggered sequence to avoid distortion Mark out, drill and bolt the post-side half to the hollow post using through-bolts with backing washers or plates, or rivnuts — not self-tapping screws alone, as the top hinge carries a tensile load Check the gate swings level, closes correctly and does not scrape Clean the welds and touch up all bare metal with cold galvanising primer and a matching topcoat Hinges: I will supply weld-on / bolt-on gate hinges rated to at least 150kg. Please tell me in your offer: What fixing method you would use on the hollow square post Whether you need me to purchase any specific bolts, rivnuts or backing plates so I can have them on site before you arrive I have a second gate of the same type. If this job goes well I will book you for that one as well — you are welcome to quote both leaves together if you prefer. Requirements: Own MIG or stick welding equipment, plus angle grinder, drill and metal drill bits Access to power, or your own generator Demonstrated experience with gate and fence welding — please mention similar jobs in your offer

Title: Join and secure two outdoor barriers to concrete We need someone to install two existing metal barriers outside our restaurant in Camberwell. The job involves: - Positioning the barriers and connecting them securely together - Drilling into the outside concrete floor - Securing the bases with suitable concrete anchors - Making sure both barriers are stable and secure for outdoor use We have the barriers and metal bases shown in the photos. Please supply your own tools and any additional brackets, anchors or fixings needed. We want to leave the barriers outside permanently rather than move them in and out every day. Please quote your total price, including labour and materials, and let us know how long the job will take and your earliest availability. If this is the public footpath, confirm permanent fixing is allowed under your outdoor permit before drilling.

I’m looking for an experienced fencing contractor to install a safety barrier around my outdoor spa in Templestowe Lower, VIC 3107. Manningham Council has advised that the spa requires a safety barrier to meet the required standards. Spa size: approximately 2.27m × 2.27m Existing gazebo: the four posts form a square of approximately 3.6m × 3.6m around the spa. Please see the attached photos for reference. I’m looking for someone who can: - Recommend the most practical barrier/fencing solution for the existing setup - Supply and install the barrier - Ensure the completed barrier is compliant with Victorian spa/pool safety requirements - Work around the existing gazebo posts, tiled area and garden - Install a suitable gate if required I’m open to different fencing options and would prefer to discuss the best solution after an on-site inspection. Please include your estimated price for materials and labour in your offer. Location: Templestowe Lower, VIC 3107 Thanks!

Remove old fence Install new fence

New lattice panels secured to new pailing fence. Two other panels to fence. Possibly look at other jobs to be done.

I have 9 bamboo panels (100x240cm)to install to the existing fence to increase height to create more privacy.

See last photo - Replace wooden side gate as is - has to be sane style

Seeking fence replacement Requiring 2 metre fence height Approx 9 metres long Existing fencing will be removed

Task: Remove Existing Side Gate & Supply and Install New Colourbond Gates Remove existing side gate then then supply and install a new black Colourbond gate system. Scope: • Remove existing gate/fence • Supply and install galvanised steel posts • Supply and Install two matching black gates, metal (colourbond or similar), either solid or vertical posts with minimal gaps • Side gate posts to be 75x75x2mm gal posts, 1.95m in height out of ground to match gate height. • Posts to be set in concrete in post hole, approx 70x80cm deep. • Gates to be hinged off posts. • One gate to have pad bolt to ground, the other gate to have a keyed handle to secure. • Gates to open inward (ie. Towards back of the block) • Approximate width of driveway: 3.5m (building to boundary fence) • Desired height: 1.95m • Ensure gates are level, secure and operate smoothly Easy access. Please include all materials, and labour costs in your quote (disposal of old gates not required). Photos attached.

I have three x 2400 fence extensions which I would like added to my fence. Please provide quotes.

INSTALL NEW FENCE ABOUT 5.5M LONG REPAIR SOME AREA. PHOTO ATTACHED.