Find trusted local electricians in Blacktown

Install Downlights in a Single Storeyed House. Appx 30 Downlights The house does not currently have downlights May need to install LED Strips and some other electrical work I will supply all materials or you can quote me for supply as well

Disconnect power point and put new one in about 70 cm along wall to where x is in picture Power point supplied and old hole repaired by myself

Replace oyster light with new fitting and install new power point in the internal garage.

Hi, I am looking for a licensed electrician to install downlights in my single-storey villa. I would like to install approximately 26 downlights in total: Bedroom 1: 4 lights Bedroom 2: 4 lights Bedroom 3: 4 lights Dining/Kitchen area: 8 lights Garage (approx. 5.5 m × 5.5 m): 6 lights I would appreciate professional advice on the final number and placement of lights to ensure good lighting coverage. The job is in Blackett, NSW 2770. I am offering $1040 (supply and installation), Final payment will be adjusted if the number of lights changes after your assessment. Thank you.

Hi, I am seeking a licensed electrician to carry out the following work and provide all required electrical compliance documentation upon completion for home insurance purposes. Scope of Work 1. Install 1 new power outlet behind or near the TV in the living room. 2. Install 2 new power outlets in bathrooms for electric bidet/toilet seats. 3. Remove 2 existing ceiling fans and install 2 chandeliers in their place. Please provide: 1. A fixed-price quote for the complete job (I am not seeking hourly-rate quotations). 2. Whether a site inspection is required before providing a fixed-price quote. 3. Confirmation that you are a licensed electrician and can issue the appropriate Certificate of Compliance / Certificate of Electrical Safety (as applicable) upon completion. If a site visit is required, please let me know your availability. Thank you, and I look forward to your response.

1. Replace 2 power points in living room and kitchen. One side of the power point currently does not work. Power points will be supplied. 2. Replace 1 switch in living room. Switch will be supplied. 3. Install 2 new power points. 1 in a room and another one in the garage. Power points will be supplied.

28 Panels. Clean & Clear: Remove any existing pigeon nests, debris, and droppings from underneath the solar panels before installing the mesh. Install Mesh: Install PVC-coated galvanized steel mesh around the outer perimeter of the solar panel array. Side-by-Side Overlap: Mesh sections must be installed side-by-side with a 2-3 square overlap at the joints to ensure there are absolutely no gaps. No Drilling: You must use non-invasive solar panel clips (no drilling into the frames to avoid voiding the warranty). Mould to Roof: The bottom of the mesh needs to be neatly contoured and flush against the roof profile so birds cannot squeeze under.

Switchboard upgrade Install timer for CL2 so that water heater works on inverter.

Electrician to - 2 fan disconnect from parklea, put a cap on and install both in north kellyville home - disconnect tesla charger and install at new place where connection is already in place. Photos attached

My uncle’s bathroom light switch has stopped working and the light will no longer turn on. Looking for a licensed and insured electrician to: * Diagnose the cause of the fault * Confirm whether the issue is the switch, wiring, fitting, bulb, or something else * Purchase any required replacement parts (I will reimburse reasonable material costs with receipt) * Complete the repair and test that everything is working correctly Requirements: * Current electrical licence * Public liability insurance * Own tools * Able to provide advice if additional work is required Please include: * Your licence details * Your availability * Whether your quote includes diagnosis and labour only, or labour plus minor replacement parts I’m looking for a practical, cost-effective repair rather than a full replacement unless necessary. He is retired, doesn’t drive and is not well at the moment so can’t organise this himself and i’m too far away to assist. Flexible on time of day.

20amp rcd and mounting bracket supplied, 2.5mm twin and earth cable already in the electrical box, just needs to be wired up. The new circuit is for roller shutters in the house. All other connections are done and the end of the circuit is capped off and within a junction box. Zero cuts in the wiring it's all 1 x 2.5mm twin and earth and the corrections are made with correctly rated quick connects and factory supplied cables with 10amp 3 pin plugs.

Install a new power point in garage ceiling to power the autmatic door opener.

Need a licensed sparky to install a Shelly Pro 3EM-3CT 63 (3-phase energy monitor) into my residential switchboard this Saturday. The job: Install 3 × split-core CT clamps around the 3-phase mains cables between the meter output and main switch Mount the Shelly Pro 3EM unit (DIN rail or adjacent) Wire a 240V AC feed to power the unit (from a spare MCB or existing circuit) Verify it powers up and CTs are reading What you DON'T need to touch: The Endeavour Energy revenue meter (Elster A1100), sealed, stays as is Service fuses Solar inverter or array wiring Any existing circuits What's already here: 3-phase board, dual supply (grid + rooftop solar) Elster A1100 meter, Endeavour Energy network Tenby Cables switchboard, Left + Right modules The Shelly unit and all 3 CT clamps — I have everything, just need it installed I'll provide: Full installation guide with wiring diagram (already prepared) Photos of the switchboard for your reference (attached) The Shelly Pro 3EM unit + 3 CT clamps (all supplied) You'll need to bring: Short length of 35mm DIN rail if there's no spare space on the existing rail (board looks fairly full, may need to mount a small rail segment on the back panel) 1 × MCB (6A or 10A) to protect the Shelly's 240V power feed Short lengths of wire for the 240V feed (L + N to the unit) Location: Kellyville Ridge, NSW When: This Saturday — flexible on time, morning or afternoon Budget: $150 – $200 This is a straightforward install, no modifications to existing wiring, no meter work, just clamp-on CTs and a small monitoring unit. Should take 30-45 minutes for anyone familiar with switchboard work. Must hold a current NSW electrical licence. Happy to see your licence number before confirming. Cheers!

Install the light to the ceiling

Need to replace 2 Switches and 1 x 3 Gang. All materials supplied. Just need expertise to replace them.

Hi I need a replacement of 4 light switches and our bathroom exhaust has stopped working. I have only put $10 as budget can be discussed. Location is Blacktown NSW 2148.

Replace 16 x downlights - will supply new downlights

I need an electrician to add some extra electrical points 5-6, install new lights (5-6) both internally and externally. Please quote your hourly rates.

Need a licensed electrician to supply and install a smoke alarm (prefer brand clipsal). The current one which needs to be replaced is a hard wired with 9v backup battery smoke alarm.

Please note that this is a double storey house. The power outlets have already been purchased from Bunnings and are available on site. This is a new installation, so there are no existing outlets in those locations to replace. The roof space is accessible. I would like the work to be completed by Wednesday this week