Find trusted local electricians in West Melbourne

setting up pendant lights and sockets.

Need 1 Air conditioner installed including electricals. Back to back and 14m from meter box same wall. Split reverse cycle system. Single story. 8.8 KW system.

Hi, I'm looking for a fully licensed and experienced electrician to install two new ceiling fans. I will provide the fans. It's a single story home with 2.7m hight. One in the living room One in the bedroom

I need a power point installed for my front sliding gate. There's a concrete that will need to be cut through ( 600mm length ) max. This will need to be flushed afterwards.

I need to put the intercom back on the wall. I need to install disability buttons.

I have a ac unit that has started to leak water from the front. Wanting someone to check diagnose and fix the issue. Photo attached

Various electrical work. Install new remote control ceiling fan. Replace existing pendant lights with new pendants (supplied), 1 double pendant (supplied) to replace existing triple, 3 singles pendants (supplied) to replace existing singles over kitchen island bench. Install new power points x 7 (supplied) Please message ONLY if you have requisite electrical skills and qualifications. House is brick veneer single story 4 years old. Colourbond roof.

Hi, I’m looking for a licensed electrician to remove and replace four existing pendant/chandelier lights in my home. • Old pendant/chandelier lights need to be removed • New lights are already purchased and ready to install • Ceiling wiring already exists • Installation is indoors (dining/kitchen area – see photos) Please bring your own tools and ensure all work is done safely and to electrical standards. Let me know: • Your availability • Cost Thanks!

Our apartment has a balcony and the electrical power point has stopped working. We also need to re-affix a lose one and install a USB compatible power point in the kitchen.

Help me to upgrade from fuse to circuit breaker

Looking for a licensed electrician to replace two downlights. One if the kitchen and one outside the front door. They are hard wired

Move switch in New location approximately half a metre and move light to centre of the room and look at ensuite power on the same circuit as slight switch

Need an electrician to install a new double power point on the wall. The wall sits behind one that has a power point

Electrician Required – Safety Certificate for Non-Operational Café We are seeking a licensed electrician to inspect a café premises that is currently not in operation and provide the necessary electrical safety certificate to restore the electricity connection. Location: Laverton North, VIC Availability: As soon as possible If you can assist, please get in touch with your availability and a quotation

Replace two old ceiling lights. First is kitchen replaced with new round fluorescent. Second is dining room, replace with 3-way LED spot light. New lights supplied.

Need to change HFC NBN port location. Currently it's in the living room and i'd like to change it to my bedroom. Theres an old ADSL port thats currently in the bedroom which might help with drilling.

Out outdoor wall lights don't work. Lights are less than 2 years old. Suspect its the power switch that's faulty. Need a licenced electrician to check/fix the issue.

Hi there, I’m looking for a qualified electrician to help fit two hanging pendant lights. The power points are already in place; the task involves safely removing any existing fittings and installing the new pendants. Details: 2 pendant lights to be installed 2.7m ceiling height Power and switch wiring are already available Must bring your own tools and ladder Requirements: Licensed electrician only Experience with pendant light installations Ensure all work meets Australian electrical standards Attached are the installation points and pendant lights instructions for one of them.

We require a licensed electrician to install and connect 3-phase power in our factory for: 1. Light Gauge Steel Roll-Forming Machine (main equipment) 2. Battery-powered Forklift Charger (Lithium) – requires a 3-phase outlet connection from the same supply ⸻ Scope of Works • Run approx. 30 m of 16 mm 4C+E circular orange cable (see photos). • Install 40 mm rigid PVC conduit with 90° bends neatly along wall and ceiling (route shown in red in photo). • Connect to existing main distribution board inside the office area (see photo). • Install and wire: • 1 × 40 A 5-pin 3-phase outlet (IP66) for the roll-forming machine • 1 × 32 A 5-pin 3-phase outlet (IP66) for the forklift charger • Supply and fit appropriate RCBO / MCB protection as per parts list. • Test, label, and commission both outlets for safe operation. • Provide certificate of electrical safety on completion. ⸻ Materials Supplied On-Site • 30 m – 16 mm 4C+E circular unarmoured orange cable • 10 × 40 mm rigid PVC conduits (4 m lengths) • 90° conduit bends • 3-phase outlets and plugs (40 A & 32 A IP66) • Distribution board enclosure and circuit protection devices (see parts list) ⸻ Requirements • Fully licensed A-Grade electrician with industrial experience • Own tools, consumables, and ladders if required • Must provide Certificate of Electrical Safety upon completion. (I will organise scissor lift) ⸻ Photos Attached 1. Factory wall and conduit path (marked in red/blue) 2. Main distribution board location (office) 3. Orange 3-phase cable roll 4. Supplied conduits 5. Parts list with all supplied materials ⸻ Preferred Start: ASAP (factory is ready for works)