Find trusted local electricians in Brisbane

I am wanting to relocate the point of attachment (POA) for my overhead electricity service line approximately 1 metre from its current position on my house, using an approved raiser/extension bracket rather than installing a private power pole. Have been told by Energex a fairly straightforward setup: the service cable (the black aerial bundled cable) terminates at a simple strain/dead-end clamp bolted directly to the timber fascia board, right beside where the meter/service fuse enclosure is mounted on the wall. Happy to consider the simplest/cheapest solution - whether that’s a raiser pole or just moving this same style of clamp/bracket out roughly 1m from its current position, likely along the same fascia line or onto an extension arm fixed to the fascia or roof structure. Hoping dearly not to relocate it too far from the existing point because the main switch board is at ground level underneath this position. The fascia/eave here is timber, which matches what I mentioned earlier — that takes coach screws into solid timber rather than needing masonry anchors, so a Level 2 electrician should have straightforward fixing options for a new bracket position. Energex are replacing the line out the front which prompted their visit and I have started recent works on the front of my property (approved plans through Council) that apparently didn’t consider Energex’s requirements. Energex have told me that Moving the point of attachment out 1m will change that angle and the amount of slack needed. Hoping too that the the aerial attachment point itself is the only thing that needs relocating with the existing fuse/meter run staying put. Happy to be advised.

Need an electrician to move two outdoor lights and one inside socket in order to accommodate an expanded door.

Hi, I need a quote for: replacing/installing a 2 burner cooktop (30x51cm), installing a second hand oven (59x58cm), repairing a sealed bathroom light, and checking a Smeg dishwasher. Please advise availability and callout fees. Thanks!

I would like a wall light hung on the wall. It will be hung in the corner. Pictures of the light and corner attached.

Need an electrical cord outside put in a conduit and connected to previously installed garden lights

Licensed and insured electrician required for kitchen renovation in a Windsor QLD unit. Target October 2026; two coordinated visits. Indicative budget $750 for existing-position kitchen services. Quote incl. GST if applicable. BEFORE DEMOLITION: isolate/disconnect the existing freestanding cooker and affected kitchen electrical fittings as required, making the area safe for cabinet/splashback removal. AFTER INSTALLATION: refit affected kitchen electrical fittings, test and provide required completion documentation. Retained stove is assumed GAS, with gas disconnection/reconnection and appliance securing in a separate plumbing/gas package. No new cooker supply. Include fit-off of affected existing-position kitchen outlets and installation/connection of our supplied compatible rangehood to existing suitable provisions. Cabinet/hood cut-outs by cabinet installer, coordinated with you. Include minor connectors, fixings and ordinary consumables. State how many outlets your offer covers. Verify retained stove/oven model. Include safe treatment of existing ignition power where applicable. If the unit has a hardwired electric oven, separately itemise its disconnection/reconnection; that extra oven work is outside the $750 base allowance. Gas work is by the separate licensed gas fitter. Retain service positions where practicable. New circuits, switchboard upgrades, major rewiring, masonry chasing, new ventilation duct routes and building penetrations are outside base allowance; inspect and quote any necessary additions separately before work. No under-cabinet lighting requested. Existing kitchen photo and proposed Kaboodle 3D image attached; verify dimensions on site. Check appliance dimensions, clearances and rangehood compatibility before work. State licence/insurance, availability for both visits, inclusions, testing/documentation, exclusions and any return-visit fees.

The plug for of the fridge sticks out of the wall too much. So it needs to be recessed

Need to replace two light fittings in a master bedrooms.

Looking for a licensed electrician to install 8 x double power points. I already have the power points, so labour only. New install: 3x in living room 3x in garage 1x TBC To replace: 1x in hallway Plasterboard walls, with existing power points on the same walls nearby.

New Bosch induction cooktop to be installed to existing cut out. Old cooktop to be removed. Qualified electricians only.

I have two existing hard wired smoke alarms which need replacing, and 4 new wireless smoke alarms to install. All alarms are provided and come interconnected. I understand a qualified electrician is required to install the hard wired alarms.

We’ve got 4 light switches that are stuck and/or pressed in. Want to get these fixed so they’re no longer stuck. Located in Bowen Hills

Need a licensed to electrician to replace a circular fluorescent fitting with a downlighting

Please quote on: camper trailer has a standard 15 amp plug in fitting to take 240V power (eg caravan park). I just need the wiring done from the inside of this fitting to a new (already purchased) Powertech double RCD protected GPO, which sits in an existing box which bolts onto the camper. Very simple and fast job, there was a standard double GPO already installed previously. The new GPO has been purchased, just labour time involved, estimate 5-10 minutes max, please quote

Need an electrician to be available to run power for future split installs. I'm a fridge/air con tech myself, I just need someone that I can rely on for future installs.

Hello, We are looking for a licensed QLD Electrician to attend our retail store, on Albert St (Brisbane CBD), to replace three faulty ceiling downlights. The Issue: Three recessed LED downlights on our main sales floor have failed (flickered and went out completely). This is affecting the lighting on our sales floor, making some display areas dim. The Job: The task is to replace the three faulty LED downlights. The scope of work includes: 1. Safely accessing the light fittings in the high ceiling (a suitable ladder is required - Approximate ceiling height: 3 meters). 2. Removing the three faulty downlight units. 3. Supplying and installing three (3) new, suitable replacement recessed LED downlights and drivers. 4. Ensuring the new lights' colour temperature (warm white) and brightness match the existing lights in the store. 5. Testing the new lights to confirm they are secure and fully operational. Please note: The successful contractor MUST supply the three new compatible replacement downlight fittings and drivers. The cost for this hardware must be included in your final offer. Requirements: - MUST be a fully licensed and insured QLD Electrician. - You must have your own tools, including an A-frame ladder appropriate for a high commercial ceiling. - Experience with commercial lighting systems. Location & Timing: Location: 136 Queen St, Brisbane City QLD 4000 When: The job can be completed at your earliest convenience. Please state your availability in your offer. Please provide a comprehensive quote for the complete supply and install. Thank you.

Licensed electrician required for multiple tasks in a newly purchased property that I am doing some upgrades to. Ideally work to be done Friday or Monday. * Change light switches - 8 approx * Change power points - 8 approx * Add a new point to multi purpose * Install a new light / downlight in laundry * Change lights in bathroom x 2 * Change exhaust fan in bathroom and laundry x 3 total * Test other lights / change bulbs Quote is just for labour. Equipment has not been purchased yet but can be on advise.

Need these items moved as pictured below. • A/C Controller • Intercom • Light • Powerpoint (FYI - I’ll organise to have the old holes patched)

Simply a double power point installed on the weatherboard wall.