Find trusted local electricians in Inner South West Sydney

I need exactly what’s in the photos x1 double plug wall socket and one 32amp plug

Change switch on chandelier to different section downlight

Pendant light installation in Kitchen

Connect power outlet under house to plug in an inline fan. Connect on/off switch for in line fan, 1mm cable for switch installed from wardrobe penetrating through floor. Approx 1 metre clearance under house. Change light fixture in laundry

Licenced Electrician only I need to move the PowerPoint two tiles across from the window Please see exact location where the red tick is shown on the image I need to change it from a single PowerPoint to a double PowerPoint

To install 6 down lights power points and switches

Hi, I need a licensed plumber/gas fitter and electrician (or dual-traded tradie) to install a rangehood, connect a gas cooktop, and hardwire an electric oven in Rockdale. Preparation: Old appliances are fully removed and space is clean. Straight swap — no cutting or cabinet modification needed. 1. Rangehood: Mount new rangehood into cabinet and plug into existing power point inside. 2. Gas Cooktop: Connect new gas cooktop to existing gas line. 3. Electric Oven: Hardwire new oven to existing wall power cable. Requirement: Must be licensed and provide license number / receipt for appliance warranty purposes. Very quick and easy job as everything is fully prepped. Flexible with day and time. Please leave your offers!

8 new PowerPoints, power is all there just need to be shifted location either a bit to left or right etc to design new kitchen. Hard wire power for oven and installed oven and microwave. LED strips installed 15m with switch Install range hood with vent to eve Supply all material from start to finish and when splash back is on come and just add the PowerPoints, oven and etc. Wall is double brick all power and etc was there from exisiting kitchen. Don’t ask to show you pictures because it will basically be a brick wall with nothing on it but the old PowerPoints etc.

The RCD labelled “Protected Power” (C20, 30mA) trips the instant I switch it on, so all power points are dead. Lighting circuit is fine. Cause is known: insecticide spray went into one power point and the tripping started immediately after. The RCD has been off since and I haven’t touched the outlet. What I need: the affected outlet inspected and replaced, and the circuit tested.

I currently have a Martec Contour 2 connected to a 3 gang switch and the fan exhaust is not working so needs to be replaced. The main bathroom lights and lights on Martec unit are on the same switch. I plan on buying Martec Profile 2 and need an electrician to help replace and connect to 3 gang switch. This may require existing cutout to be extended to fit new system. Any recommendations on any other bathroom heater and fan exhausts are welcomed.

I have an external power point that I need installed by a licenced electrician. I will supply the materials (external weatherproof power point)

I need to replace 2 power points and 2 light switches. 1 set is in the bathroom on a tile and the other is in bedroom. I have the replacement parts. Just need to replace them and fit them on the wall/tiles

I am looking for a fully licensed NSW electrician to supply and install one new extra power point in a bathroom at a single story house in Padstow and able to provide CCEW. Just take extra care of the wall tiles.

I'm looking for a licensed and insured electrician/gas fitter to complete the following work at my property in Arncliffe, NSW, as soon as possible. Scope of work: Rangehood Replacement Remove existing rangehood. Supply not required (I already have the new unit). Install a new Solt 60cm Slide-Out Rangehood (Stainless Steel). Gas Cooktop Replacement Remove existing gas cooktop. Install and connect a new Chef 60cm Gas Cooktop (Stainless Steel). Ensure the appliance is tested and operating safely after installation. Requirements: Must hold the appropriate licence(s) to carry out the work. Please bring any standard installation materials if required Please provide a competitive quote before commencing the job. An invoice is required upon completion. The job is located in Arncliffe Please contact me with your availability, licence details, and quote. Thank you!

Need a licensed electrician to replace 3 light switches, 3 double power points and 1 bathroom batten light fitting. I have already purchased all the replacement fittings. Please install them and test that everything is working properly. Photos attached

Need some cables running in kitchen for new power sockets On the image, the Red is existing power The left hand corner is where the mains power for the cooker is which will need running behind to where the new cooker placement is going. I’ll need power new slot which is the green section and there is another PowerPoint below at the bottom of the kitchen the back which will be used for the cooktop but currently doesn’t seem to be given off any power.

I have purchased a ogemray smart relay 25a (powered by shelly) so I can control my hot water from the Shelly app. This can be installed in the fuse box of inline, near the hot water. It is a simply job that I could do myself, but I prefer an electrician to do it. I would like someone today or tomorrow if possible.

Hello! I'm looking for a licensed electrician to replace two existing ceiling light fittings (one in each of two rooms) with new pendant lights that I have already purchased. Job details: Remove 2 existing ceiling light fittings. Install 2 new pendant lights (supplied by me). Ensure both lights are securely fitted, working correctly, and safely installed. Please bring any standard tools and small installation hardware that may be required. Preferably today or tomorrow. Thank you! 🙏 Magda

Looking for a licensed electrician to supply and install a hardwired smoke alarm in a bedroom and provide the required compliance/certificate on completion. Details: - Single smoke alarm installation required. - Ceiling is standard plasterboard. - Existing downlights nearby (see photo). - Must be hardwired and compliant with NSW requirements. Must provide Certificate of Compliance for Electrical Work (CCEW) upon completion. Please include supply, installation and certification in your quote. Looking to have the work completed as soon as possible.

I need a licensed electrician to replace 10 power points and 10 light switches throughout my home in Kogarah. This is a straightforward like-for-like swap - same locations, no new wiring runs. I’ll purchase the hardware and will be ready on the day. The job: - 10 double GPOs - swap only - 10 light switches - swap only - All items in the one property, one visit Requirements: - Licensed electrician only The date of this task is flexible and will be at the tail end of a kitchen renovation, looking around w/c 20th July.