Find trusted local electricians in Baulkham Hills & Hawkesbury

Install 2 dimmers Fix flickering bathroom light change globes Assess outdoor heaters

Only 3 phase main switch and breakers to be installed. rest of the circuits of the house will remain on one phase. Level 2 electrician. No private pole

In my garage is a power point that has 2 standard plugs. Want to get the quote for upgrading to 15A for Tesla mobile charging. New power point next to switch board can be other good option. Thanks

Looking for electrical apprenticeship to make money after training for Beyond Lift One month Free training at our Factory in China. • $70,000 + tool $ (6 - 9 months Training after Factory visit) • $120k and more once you become independent installer (Mostly 9 months - 1 Year) • Accomaodation and fuel is provided for travel to over 100Km travel

I have Jinko Solar 370W solar panels with Growatt 5kVA Single Phase Inverter and it has stopped working, need someone to take a look and fix it.

Remove light fixture (billiard lights) and replace with another light fitting (single weave drop light)

Install wall charger for Tesla. Installation is needed in garage, switchboard is on the same side, 10 m from Garage. There is already a switch in the garage next to where we need wall charger installed.

The wiring for the water heater at the power board needs to be done to off peak. Currently on on peak. Also need a timer in that so the water heater only operated off peak during the day when my solar is on

I have an aquamax 340 gas water heater, and has been working fine. I had to move it up 30cm for some backyard work so the connections were altered. I got a plumber to do it for me. However right after the work has been done, the water pressure dropped massively. Plumber used fittings of same width as before, and the heater company saying it’s a plumbing issue.

We have recently moved to a house with solar panels. Photonof inverter attached, but it’s not sending anything to grid and I need help to figure out what’s wrong and what we need to do to fix it,

I would like a ceiling fan with light installed in my lounge room. There is currently a light fitting with single switch at entrance to the room. My photos show the ceiling and roof of the room, and the external wall that is opposite the light switch. (I’m not really sure what an electrician would need to know/see.) I will pre purchase the ceiling fan/light.

Install 4 power points(All have wires nearby Install 1 oyster light (Old one has been taken out already, just need to install new Change 1 light switch

I need my front light sensor fix and 2 smoke detectors and light switch fix

Downlight installation and sensor installation - View all the details of this offer: https://www.airtasker.com/offers/01JY5JC2PSFVK0DJFBR6W17G81

Install downlight and sensor - View all the details of this offer: https://www.airtasker.com/offers/01JY5J3J56J9GP7E3X8WQZAY4X

Install a supplied heat/fan/light into ensuite bathroom on 2nd floor. New circuit to be run. Install a supplied fan/light to replace existing light in laundry. No ducting required.

Install power point and sensor - View all the details of this offer: https://www.airtasker.com/offers/01JXMDZYMPH4KCZQ1MAB4CTYH3

Need to replace three lights as shown in the picture. Please replace them with bunning lights as shown in the link. Kindly request you to purchase lights from Bunnings https://www.bunnings.com.au/arlec-5w-bordon-led-step-light_p0183679

We’re looking for a licensed and experienced electrician in Sydney to help diagnose and fix a recurring issue with our home’s electrical system. The issue: • One phase of our multi-phase system is tripping the breaker (RCD), usually ~15 minutes after switching it on. • This started after heavy rain last week and has persisted even in dry conditions. • A similar issue occurred in another phase previously and was traced to water ingress in a hidden junction box. • We’ve ruled out appliances—fridge, dishwasher, and microwave are unplugged—but the breaker still trips. • There’s no visible water damage or burnt smells, but we suspect moisture is still trapped in a junction box, conduit, or wiring insulation. What we need: • Urgent on-site inspection to trace the fault in the affected circuit. • Identification of the hidden junction box (we have electrical blueprints to help locate it). • Insulation resistance testing (megger) or circuit tracing tools may be required. • Fix the fault—most likely involving sealing, replacing, or rewiring affected components. Please bring the necessary tools and safety gear. Access to electrical drawings will be provided. Ideally looking for someone available ASAP. Let us know your availability and experience with similar water-related electrical faults.

Looking for LED strip light installation