Find trusted local electricians in West Melbourne

Need a qualified electrician to move a 2 in 1 GPO / light switch and standard light fitting relocated in under stairs room. FYI, we've removed the door, door frame and are expanding the opening and as a result the existing GPO and light fitting just need moving 300 mm. The drywall is in an understairs cavity, and the wall is currently being cut back, so the access is pretty easy for this job

1940’s house build. Need fuse box upgraded!

Hi, Need to fix my gas water heater. Pilot light goes off as soon as brought to flame position. Brand name is aqua max. google says most likely need clean/ change of thermocouple. ASAP please the pic is the same as what i have.

Need a helper to my electrician on site for today.

We have around 8 pendant lights, 2 TV wall mounting to be done

I want to fix one power point , fix kitchen duct and look at one of calling fan. Also run conjute from existing power point to new one for pump. And fix earthing

Switch board to be changed & 7 hanging lights to be hanged on roof

Installation of the following: - Linear light above kitchen island bench (needs wiring) - 2x external lights (already has existing wiring) - Exhaust fan in WC (needs wiring) Single storey house

Move switch in New location approximately half a metre and move light to centre of the room and look at ensuite power on the same circuit as slight switch

Need an electrician to install a new double power point on the wall. The wall sits behind one that has a power point

Electrician Required – Safety Certificate for Non-Operational Café We are seeking a licensed electrician to inspect a café premises that is currently not in operation and provide the necessary electrical safety certificate to restore the electricity connection. Location: Laverton North, VIC Availability: As soon as possible If you can assist, please get in touch with your availability and a quotation

Replace two old ceiling lights. First is kitchen replaced with new round fluorescent. Second is dining room, replace with 3-way LED spot light. New lights supplied.

Need to change HFC NBN port location. Currently it's in the living room and i'd like to change it to my bedroom. Theres an old ADSL port thats currently in the bedroom which might help with drilling.

Out outdoor wall lights don't work. Lights are less than 2 years old. Suspect its the power switch that's faulty. Need a licenced electrician to check/fix the issue.

Hi there, I’m looking for a qualified electrician to help fit two hanging pendant lights. The power points are already in place; the task involves safely removing any existing fittings and installing the new pendants. Details: 2 pendant lights to be installed 2.7m ceiling height Power and switch wiring are already available Must bring your own tools and ladder Requirements: Licensed electrician only Experience with pendant light installations Ensure all work meets Australian electrical standards Attached are the installation points and pendant lights instructions for one of them.

We require a licensed electrician to install and connect 3-phase power in our factory for: 1. Light Gauge Steel Roll-Forming Machine (main equipment) 2. Battery-powered Forklift Charger (Lithium) – requires a 3-phase outlet connection from the same supply ⸻ Scope of Works • Run approx. 30 m of 16 mm 4C+E circular orange cable (see photos). • Install 40 mm rigid PVC conduit with 90° bends neatly along wall and ceiling (route shown in red in photo). • Connect to existing main distribution board inside the office area (see photo). • Install and wire: • 1 × 40 A 5-pin 3-phase outlet (IP66) for the roll-forming machine • 1 × 32 A 5-pin 3-phase outlet (IP66) for the forklift charger • Supply and fit appropriate RCBO / MCB protection as per parts list. • Test, label, and commission both outlets for safe operation. • Provide certificate of electrical safety on completion. ⸻ Materials Supplied On-Site • 30 m – 16 mm 4C+E circular unarmoured orange cable • 10 × 40 mm rigid PVC conduits (4 m lengths) • 90° conduit bends • 3-phase outlets and plugs (40 A & 32 A IP66) • Distribution board enclosure and circuit protection devices (see parts list) ⸻ Requirements • Fully licensed A-Grade electrician with industrial experience • Own tools, consumables, and ladders if required • Must provide Certificate of Electrical Safety upon completion. (I will organise scissor lift) ⸻ Photos Attached 1. Factory wall and conduit path (marked in red/blue) 2. Main distribution board location (office) 3. Orange 3-phase cable roll 4. Supplied conduits 5. Parts list with all supplied materials ⸻ Preferred Start: ASAP (factory is ready for works)

2 x Pendant Lights to be wired and installed on top of Butchers Bench in Kitchen area

Needing solar panel bird mesh installation. Approx 30-40m perimeter . Double storey house

6 new electrical plug sockets to be installed in my house.

Hi there, I’m looking for a qualified and licensed electrician to carry out the following work: Job details: Replace the existing tube light in a room with a new dimmable lighting setup (so brightness can be adjusted depending on the time of day). Install a dimmable switch (photo attached) for the new lights. Require two lights to be installed in total for the room. The kitchen tube light is not working – please inspect and, if it needs replacement, use the existing room tube light for that area. Requirements: Please quote including the supply and installation of suitable replacement lights and dimmer switch. Must be a qualified and licensed electrician. Tax invoice and electrical compliance certificate will be required upon completion.