Find experienced local carpenters in Ryde

Finish carpenter, Joiner for architraves, cladding required Some experience required On-site work, some workshop work available Fit internal wall cladding, architraves, skirting Help/take direction from other carpenter joiners on site Own tools not required Be able to use a drop saw/power tools Be on time and have a positive attitude

Demolish and removal of floor mounted kitchen joinery. - Removal of floor (only) joinery - Removal of a bench top - Removal of p trap - Remove tile - Disposal

Building bulkheads installing joinery adjusting doors

One drawer to be converted into a hinged door. Front panel of drawer to be removed and converted into a fixed panel and hinged cupboard door. Two photos show the existing drawer and the third what we need it to look like with the fixed panel and hinged door. We’re having a retractable screen installed on the bifold door next to the unit and we won’t be able to open the drawer. Hence the need to convert it into a hinged door.

Joinery for BBQ area — a little over 2.7m wide, and 82cm high. Thinking of a unit of drawers on the left-most 20-30% and 2 double-door cupboards for the reminder 70-80% of the total 2.7m width (but open to better ideas). There’ll be a drop-BBQ and sink that dips into the cupboard areas (in the concrete cutout areas). Alfresco area where this sits is overhead covered, but can get some sideways rain and/or “pateo washing” wet, so Compact laminate or similar suggested. Prefer light wood-look with some texture (eg: Polytec Boston Oak Woodmat). Budget can flex as appropriate.

I have a small laundry room, and am getting new dryer soon. I want to explore options of what can be done to make this better - joinery to house the washer and dryer so I don’t have to mount the dryer (invert it) etc but looks neater.

Hi, I am after Joinery Cappings / Mouldings to 4 x existing built in wardrobes. I'm also after a drawer front to match an existing desk

I need some joinery repairs done as follows: 1) Joinery panel 2.1m X 0.6m came off the ceiling, needs to be re-glued securely as it's a heavy panel. 2) Joinery door of cupboards below BBQ on terrace came off due to loose/corroding hinge &/or screw holes 3) Vertical battons glued on to joinery panel at entry have come loose, needs to be re-glued with clear glue. I have attached photos of each of the three areas. I would prefer someone with experience in cabinet making or joinery. Thanks

We have a small storage space with the following dimensions: Height – 241cm, Depth – 117cm, and Width – 98.5cm. We're looking to convert this area into a compact study nook based on a design we’ve already prepared. We'd love someone to help bring this to life.

Hi! Thanks for the offer! We can arrange a time for onsite inspection for accurate quote. Generally I need the following job done: 1. Fridge area door and bottom removed 2. Washroom Shelve cut and installed 3. Waste removed

Office renovation: A new floating desk, wall to wall Drawers Floating shelves and enclosed bookshelves LED lighting Attached a plan sketch. All measurements in cm

40 yr old large solid robe. Door operates on pivot hinge now rusted out. Need to hinge differently. I believe this is possible but tricky.

Need to join panels on a dishwasher that is embedded in kitchen cabinet

Joiner to make custom designed laminated workbench /benchtop from 32 mm thick MDF for home office. 330 cm long, 85 cm depth, supported with 40 cm wide, 50 cm deep chest of drawers on either sides and shallow drawers (under the benchtop) in the middle, supply and install

I have an ikea office wall cabinet (1200mm x 1280mm) that I need to be removed and cut down to reduce width ( 1200mm x 700mm) and the wooden bench below reduced from 1500mm to 1000mm. This is required to make room for a new fridge/safe ( 1800mm x 500mm). I’ll be free to assist on the day if an extra set of hands are required.

We want to get quotes for joinery and new kitchens for our upcoming new house project, we need someone good with CAD that can come out to site and we show them where we want what cabinets to be etc so you can put them on a set of plans with measurements etc so we can use it for quotation purposes

Hoping someone with joinery skills would be able to make a desk like the one in the link. I would need 2, and both around 1 metre wide. These do not need to be beautiful. Essentially a strong box with hinged lid attached to the wall.

We recently installed new joinery and need a gyprocker to box up the space between the joinery to the ceiling and for two rooms we also need a side wall/lined as well Looking for square set finish: Space in kitchen: Space above stone top: 232cm wide x 49cm high x 35cm deep Small cabinet before window: 57cm wide x 49cm high x 35cm deep Space above fridge: 130cm wide x 49cm high x 35cm deep Space in butlers pantry: 245cm wide x 49cm tall x 35cm deep Space above built in bookshelves: 306cm wide x 35cm high x 35cm deep Space above built in number 1: 200cm high x 35cm high x 60cm deep Plus a gyprocked wall on the side that is 275cm x 60cm Space above built in number 2: 100cm high x 35cm high x 60cm deep Plus a gyprocked wall on the side that is 275cm x 60cm Big built in number 3 is L shape and has a traditional curved cornice One side is 362cm width x 10cm high x 60cm deep The other side in two sections: First section: 211cm width x 10cm high x 60cm deep Second section: 102cm wide x 10 high x 60cm deep Looking for a square set finish to be sand and ready to paint. Must include all materials Flexible on timing.

Need an experienced joiner or joinery apprentice to do a range of tasks for a full day. Installing some skirting boards, installing quad trim, installing some cornice, re-hanging a door that’s has not been hung right and doesn’t fit. A full day is 8 hours of work. The work doesn’t have to be all done on the same day. A few hours could be done on Friday and the rest on Saturday for example.

I require 1 ikea metod 4 drawer assembled and installed, 2 metod wall cabinets (no door) and 2 bench tops and side panels cut to size and installed. One of those Benchtops will require a sink cutout so the old sink can be used. I will require the old joinery dismantled and discarded. Existing joinery consists of 2 drawer units, bench top, 3 sets of shelves and one metal display unit. Photo 1. Ikea design Photo 2. Ikea order form Photo 3. Existing joinery which needs to be removed (all stock will be removed for quick demolition) Photo 4/5 This is the existing sink and existing base unit which holds plumbing and hot water system which I will keep and will not need to be removed. I plan to replace the benchtop on this section. This is a commercial premises and can be accessed on Saturday from 12pm -9pm Saturday or Sunday 7am to 3pm. I would ideally like it all complete in one day if possible. - Due date: Before Sunday, October 2, 2022