Find experienced local carpenters in Albion

Need to drill a knife display cabinet on wall and drills shelf to wall as wel - Due date: Flexible

My are planning to assemble the 7 base cabinets ourselves but would like them to be fixed to the wall, having side panels attached to the cooker , dishwasher etc and have the laminate bench top fitted as well. We are having currently building works done and expect the kitchen to be delivered on the 26th September. We would hope to have them ready within a few days.

remove front fascia of current wine rack storage and remove rear panel of benches to install new wine cabinets under the bench. - Due date: Flexible

I require someone to install 6 pieces of floating shelves for a kitchen. The wall is concrete. The shelves are measured exactly (so need to cut) with holes for the brackets already built-in. All that is required is to drill the brackets to the wall and to secure the shelve to the bracket (I'm assuming the shelve will need a screw underneath to the bracket as well.) It does not come with any plugs or screws, this will need to be provided as part of the job. Shelve dimensions are: 2x(Depth=140mm, Length=700mm, thick=33mm) 2x(Depth=285mm, Length=690mm, thick=33mm) 2x(Depth=285mm, Length=1145mm, thick=33mm) The last guy I accepted stopped responding after I had accepted the offer so please do not offer if you aren't certain on the job. Thanks. - Due date: Flexible

I have two large wooden chests. I’d like them both sanded back and the brass on them polished. The large cabinet I would like the inside sanded as well. I’d like someone that is experienced with furniture restoration or wood work They need to be picked up and dropped back Location albion qld. Thank you so much - Due date: Flexible

Overhead sanding, planing, levelling underside of timber deck post ends that run along joist at 3m height. This is in preparation for an outdoor blind head box fitting. 11 x 50mm wide x 125mm long post ends with 0-2mm overhang. 1 x 125mm wide x 125mm long post end with ~5mm overhang. I have a 2.1m A frame ladder / 3.8m extended if it helps. Thanks - Due date: Flexible

Need someone to take out 3 mdf steps from internal staircase and replace them with pine steps to match the rest of the staircase. This includes sourcing timber, cutting/shaping timber and installation. See photos for reference of 3 steps. - Due date: Flexible

We need to build small bitumen ramp 2.5 meters 10 cm high - Due date: Flexible

Hi, There is a little stain I need removed. Check the attached photo. Thanks, DeeDee

Replace deck panels from Modwood to hardwood timber. Visit site at Albion to measure and discuss task for quoting. Quotes to be in by 7th April.

Hi there, I’m building a bedside table and need some help with cutting my 16mm MDF to size. I have all the sizings required and need about 6 or so pieces cut. I’ll come to you, of course.

Slight water damage with 2 vertical panels in white melamine - Due date: Flexible

I am renovating a townhouse and require a carpenter for number of tasks. - Due date: Flexible

Looking for a builder/carpenter to do a few odd jobs including: Installing 16 small brass handles in laminex cabinetry. Putting two brass hooks into concrete wall. Resize a small piece of laminex to size for bench seat. Fill a 2 metre long gap (couple of cms) between base of wall and tiles. Preferably before 8am or After 7pm as we are a beauty salon. - Due date: Before Friday, 15th Oct 2021

Yellow tongue flooring needed probably: 8m by 4m. Nail in over the outside deck. The deck is a bit weathered, so need someone good at making it flat and balanced with no hollow gaps. Will need waterproof sealant to go over it, because it's for outside. Will need to buy the yellow tongue and bring. Looking to cover that with some plastic floor boards to make an outdoor studio. Probably could do this myself, but happy for additional quote (already have floor boards).

3 sided raised garden bed made out of timber sleepers 1100 long x 700 deep x 600 (3 sleepers) h attached to a brick wall to make the fourth side I have sleepers, some will have to be cut down brackets to attached to wall, can get whatever screws are required

See pic, staunchen has snapped at weld.

Hi There - have a wardrobe that I need new doors measured and cut for (I will paint and hang). I can supply all fittings but will need help sourcing the materials. I'm think MDF will work, but not 100% sure. There's 6 doors total, 3 smaller and 3 larger. Materials not included in price.

Hi, we are looking to set up two basic shelves in our newest bar as well as finish up our bar counter. Looking for someone qualified to help us do the finishing ASAP!! This job shouldn’t take more than couple of hours. We are in breakfast creek and need to get this finished so we can open our cafe! Please make us an offer.

Need to build a deck over our existing concrete in the pergola area about 4 metres width & about 7 metres long. We will supply the Eco Deck, unless you have a better deal or cost?