Find experienced local tradies in ACT

Need to small block wall extensions rendered (check pictures) one is 2.1 x 1m the other is 1.2 x 1m

Reposting as I didn’t realise it expired…Looking for Mark. I have an old gas wall heater that I would like removed and disposed of. Once the heater is removed, there will be a large opening left in the wall that will need to be repaired/plastered so the wall is ready for painting (painting not required). Looking for someone with the appropriate experience to complete the job and leave the area neat and tidy.

Replace a wooden slat that has split on the door frame, drill pilot holes for magnet and reinstall magnet from old slat. Replacement slat will be on site. Will require cutting to size.

I need a hole in a ceiling plastered and sanded smooth to be level with existing ceiling please. Hole was caused by tile falling but roof since fixed. I'd like tomorrow evening for job if possible or afternoon of Tuesday 22 September before 5 pm please.

replace 4 dbl power points & 2 light switches

To render about 8 m sq entrance to house. Imagine included - it's the yellow brick area.

Looking for a plasterer to supply and install Gyprock and cornices to a 7.4m x 3.3m steel frame garage. Skillion roof. One end wall has a door/window cutout, the roller door end is completely excluded. Total area is 67m².

can someone patch my wall for a dent??

Need a bit of plastering done in the garage so a garage door can be attached to the frame

Want to put a new power point to a bedroom wall

I need help to unpack and move Sauna parts for Sauna assemblies in Downer and Casey - expect from 7.30-1pm on Wednesday 26th - your own transport is preferable

Looking for two existing power points in our living room to be converted from two to four outlets. Seeking a qualified electrician to provide new faceplates/materials and labour for combined fixed price.

I'd like someone to install my new Soundbar underneath the tv (picture refers). I've managed to hide the power cord behind the tv and want to keep the same look for the soundbar, which will mean having someone poke a hole in the wall and going under the house to feed the power cord back in, behind the tv. It's also likely we'll need another power point behind the TV too, as currently it's just a one plug power point OR an adapter* I have the correct mount, as well as the sound bar. I'd need someone to bring two brush plates to keep the wall in good shape. Note there's only about 2cm gap behind the TV and we may also need to think about a recessed wall box behind the TV OR an ultra-thin flat plug/extension cord for side entry*. *If the latter easier fixes then I'd want to negotiate price down.

Removing several power points from 2 walls in a office.

Proven professional gyprocker/plasterer to: 1. Gyprock sheet both sides of a sliding door cavity that has been removed and replaced with studs/noggins ready for sheeting. 2. A non-load bearing wall has been removed (4.5m wide *2.7m high) and gyprock sheet required to lhs and rhs and ceiling where wall removed, including adding cornice to both ceiling sides. 3. Replace gyprock sheets to several ceiling holes that were cut out as inspection ports prior to the wall being removed. Gyprock to be left to a very high standard ready for me to paint. Ignore the far wall in the photo with the insulation batts. That won’t be gyprocked as part of this work. Job can be done in 2 parts: Part 1 to be done ASAP sheet old sliding door cavity and lhs of wall where wall removed. To make way for cabinetry install along that wall. Part 2 : remainder of work over next 4 weeks.

Give us a quote for adding crown moulding to recently renovated kitchen and patch hole from wall heater that has been removed

Need a plasterer to patch up two small marks

I need a sparky to do a small job for me, check that this PowerPoint is safe (something fell on it) and put a new face plate on. I can sort out the rest (patching and painting)

Trying to hang a sensory hammock for the kids that needs to be fixed into a joist with 2 bolts. Looking for you to also chuck some spackfiller or w/e in the holes I've drilled. I’ve used a stud finder to find what I thought were the ceiling joists, but driving a nail/drill bit through hits air. The roof has a bedroom above it if that provides any useful info.

Hi all, Looking for someone to help with a small job: Replace a cracked power point cover (GPO), outlet is working fine Location: Ngunnawal ACT 2913 Happy to share more pictures Let me know your availability and experience. Thanks!