Find professional sliding gate repairs near you

Hi, I'm looking for someone to repair an electric sliding gate as soon as possible, ideally today.While reversing the car, we accidentally bumped the gate, and since then one of the wheels appears to be out of alignment, so the gate no longer opens or closes properly. I'm looking for someone experienced with automatic sliding gates who can inspect the gate, realign or repair it if possible.

Needing a section of concrete for a sliding gate track. 4.5m long

Install electric gate motor onto existing gate to replace old electrical gate motor

We want to get front fence supplied and installed, complete with automated sliding gate (for a double garage) and a pedestrian gate. The block width is 16m and fence height should be 1.2m. The design can be Hamptons (with vertical slates) having 100mm posts or any other design you may suggest.

DEA brand electronic sliding gate sensor not working. Gate seems to have power but the sensor seems to think there’s an obstruction. I’ve changed the batter in the sensor and there’s still no movement of the gate. I’ve also cleaned both sensors of dust, obstructions and other materials I need someone qualified to come have a look at it.

Material is on site. Installation only - a sliding gate. - With motor. (DKC301DC Low Voltage Sliding Gate) - Bolt rail for sliding gate.

Need help to get an extra remote for the sliding gate

I have a sliding gate just need a 4mt 40 x 40 angle tig welded on. Please supply angle as well. Photo shows current but it is too thin needs to be replaced

I need a new VACE 25/50 ultima low voltage sliding gate motor. Cables and conduits will be run to transformer

We are installing a new sliding gate with a front fence build. Conduits & cable will be run to transformer. Rack will be fitted and track will be installed.

Hi there, I am looking for aluminium fencing. I measured the size from pillar to pillar and these are: 2950 x 1000 mm 3200 x 1000 mm 2960 x 1000 mm 1885 x 1000 mm Sliding fence 5600 x 1400 mm Gate 680 x 1400mm The height of pillar is actually 900mm and the fence will be 1000mm. Let me know if this will be an issue. The colour will be Momento or Black and the pattern is the one with circles and spear at the top. Some photos attached. Are you able to do a quote based on this. Thank you.

Certified electrician needed to bring power from switchboard to gate motor.

I have a 4m x 1.5m slat gate I need installed. I have all hardware on hand, and also have concrete pad installed ready. Need hole dug for guide post (the one item I don’t have)

After somebody with some experience in making the electric VEVOR gate motor open and close at my house, as photos indicate the motor is mounted and powered up, but I’m having trouble linking the remotes/keypad etc and the magnets which shut off the motor.

Description: Seeking an experienced gate installer/repairer or gate automation technician for three tasks at a residential property in Chatswood NSW: 1. Adjust two aluminium swing pedestrian gates Two blade-style aluminium swing gates (side access and front entry) are not closing/latching properly. Adjust hinges, alignment and latch/lock strike so both gates self-close and latch cleanly. Photos attached show the gates and latch hardware. 2. Rewire/connect sliding driveway gate safety sensor The automated sliding driveway gate (Beninca) has a replacement photoelectric safety beam sensor that needs to be wired back to the controller and configured — the original was damaged and has been swapped but not connected. If the replacement sensor is faulty or incompatible, supply and install a new photobeam pair instead (quote parts separately). 3. Test driveway gate operation Full function test: open/close cycles, obstruction detection/auto-reverse via the beam, limit settings, and remote operation. Requirements: Experience with automated sliding gates and gate motor controllers essential Bring standard tools; power available on site Please review attached photos/video before quoting Advise if parts (photobeam sensor) will be extra and estimated cost Location: Chatswood NSW 2067

Sliding gate motor is working but very slow. We think the bearers inside are worn? Requires assessment and repair. Job location: Maidstone

Task Description Paint timber‑clad sliding gate on a powder coated metal frame Approximately 5m (L) × 1.6m (H). Includes full surface preparation and application of two coats (Front and Back) Paint will be supplied. Must be an experienced painter with strong, long term references. Applicants with limited experience, few reviews, or below‑average ratings will not be considered unfortunately

My driveway entry gate is not functioning properly and needs attention/service. It’s an automatic sliding gate powered by a Tau K100M motor. See photos. The gate will not open without manual effort as the cog on the motor will not grip on the gate frame (to pull and slide it open). It closes no problem. I have a video that shows this clearly. I’ve examined the parts and there doesn’t appear to be any wear and tear causing this. I suspect it just needs realignment now and then.

Change cylinder of front door lock and provide keys and help with fix/repair of sliding door

I need new sliding gate motor supplied and installed