Hire reputable rangehood installation and ducting services in SA

Installation of a new rangehood and removal of the existing one. Please attend to the job of removing the existing Robinhood rangehood and installing a new Becko rangehood at a ceiling height of 2.7 meters. The flue canopy will also be replaced. An additional cut to fit the flue is required, approximately 1 cm in circumference. The inner duct and workings are reported to be compatible. Exiting: RWBC3F933 NEW BRH90CX

Supply and Install a new rangehood

I need to get a rangehood installed in my alfresco area. Will need someone to come and have a look

Alfresco rangehood install (ACH12BBQB), Electical already complete, will need to cut through insulated panel for ducting approximately 200-250mm in width and silicone

Installation of 120cm Euro Alfresco Rangehood under a small ceiling eave in an alfresco area. Above the eave is the back of a garage with colorbond roof (front pictured). Preferably after ducting out above the roof. Eave is approx 43.5cm deep (hopefully just enough) and height from ground is 2.7m (88cm cabinet bench height to be put in which hopefully allows minimum heigh clearance). Looking firstly to confirm this product will be possible to install noting the measurements, and then for someone to install rangehood with ducting and waterproofing on roof. I can assist with any lifting required. Thanks

We currently have an existing slide-out rangehood installed, which we are looking to replace with a box chimney wall rangehood. The existing middle cabinet and slide-out rangehood will need to be removed prior to installing the canopy version. I have included link below to the canopy-style rangehood we have already purchased. Rhe electrical GPOs as indicated in the attached pictures may require alteration. When the cupboard is removed, there will likely be a void where the cupboards meet the ceiling. The cornice would wrap around the cabinetry and butt into the new chimney when installed. Minor alterations will be required to make this good. Please let me know if you need any further details or measurements. Appreciate if you can advise of the costs and timing to replace. The below is what we have bought already. 90cm Series 7 Box Chimney Wall Rangehood - HC90DCXB4 | Fisher & Paykel Australia 90cm Series 7 Box Chimney Wall Rangehood - HC90DCXB4 | Fisher & Paykel Australia Buy Fisher & Paykel 90cm Series 7 Box Chimney Wall Rangehood in steelGlass finish. Learn about its advanced features and technical specifications. Shop Now - Fisher & Paykel Australia

Need a Haeir rangehood installed. Cut cabinet and electrical installation required

Installation of a new 1200mm wide Schweigen undermount Rangehood to new bulk head in Alfresco. Colorbond metal roof with ducting and materials supplied. Power source in roof / bulk head provided.

Replace old rangehood with new one. We have the new one

Install new range hood. No elecrical work required. Drill bit required for screwing and securing into existing cabinetry, and drill bit to create a large hole for the electrical cable to go into for plugging into electrical plug point above. Simple job, we just don't have the right tools. See photos for further details.

Need to replace a new rangehood

I need a rangehood installed above my bbq also install of power Rangehood is 900mm wide

installation of Gasmate range hood 150cm into HEBEL WALL

Need a handyman to install Rangehood. I already got the rangehood. No electrical work is required. Install rangehood and vent to outside.

Canopy rangehood installation in place of fixed rangehood. Need to remove cabinet and move exhaust fan switch from the cabinet to be removed.

Instal rangehood and flu

I want to fix a restaurant rangehood Size as a below 1450 wide 1050 front to back 650 high

Replace existing 60cm slideout rangehood

Need new range hood installed canopy style 90cm and remove the old one

Rangehood installation with flute to roof and off-board motor.