Find experienced local fencing contractors in Wahroonga

I need silt fence installer to install fence 25 m around front of block

I'm looking for someone with the right tools to complete the following work at my property. Task 1 – Cut the Chain Mesh Fence Please: Cut out a section of the existing chain mesh fence. The opening only needs to be approximately the width between two vertical fence posts (see attached photo). Cut through the chain mesh neatly. Cut the horizontal steel support bar at the bottom/top (as required) to create a clean opening. Leave the remaining fence stable and tidy. Remove and dispose of the cut section if possible. Task 2 – Lay Plywood Sheets Over the Ground I will provide the plywood sheets shown in the attached photo. Please: Lay the plywood sheets over the uneven soil area shown in the photos. Arrange them to cover as much of the area as possible. Minor trimming of the plywood may be required for a better fit. The purpose is to create a flatter walking surface. Tools Required You should bring your own tools, including (if required): Angle grinder or reciprocating saw (for cutting the steel bar) Bolt cutters or grinder (for cutting the chain mesh) Circular saw or jigsaw (if plywood trimming is required) Safety equipment Photos Please refer to the attached photos for: Fence section to be cut Ground area to be covered Plywood sheets that will be provided by me Please include your quote and let me know when you're available. Thank you!

The lock/latch on my swimming pool gate is broken and needs to be repaired or replaced. I’m looking for someone experienced with swimming pool gates who can inspect the existing lock and either repair it or supply and install a suitable replacement. The gate needs to close and latch properly and comply with NSW pool safety requirements.

Install new treated pine posts along fence line (approximately 20m) push back the leaning timber fence and align to new posts. please provide your quote with detail of the job plan and warranty info.

I need someone to place the backyard wooden gate. Ideally looking for something similar

Need a quote to supply and install a colour bond or treated pine fence 1.8m or 2m in height not certain exact length at present but roughly 13 metres. See images attached

Need timber fence, 2M height around 12-15M length. Flat land. Removal and disposal of the current metal fence.

Rebuild 4.7 metres of pool fencing consisting of top and bottom rails with vertical bars. Construct new 0.9m matching gat. Re-use some existing timber but will need new timber. All construction to be treated to resist rotting and non-rusting fittings used. Work to be high quality and ready for painting.

Part of the The fence is falling, need to repair

Supply & install two gate posts (remove old posts) with new posts & then reattach the gates.

15m of 1.2m high pool fence needs replacing - please see photos. No longer keeping the fence. Supply and install replacement gate. Terracotta tiles/pavers within 2m have slipped under the fence - re-lay pavers and edge against the fence so they cant move again. More detail of scope: 1. Remove existing fence and 8 posts. Since the fence is now being replaced, no need to keep to the same post holes. Work to standard lengths where possible - so post locations can be changed. 2. Remove, level and re-lay pavers. Supply levelling sand, any materials, etc 3. Supply replacement aluminium posts and fence - Federation/Cottage Green powder coated. Similar ourtownfencing web site - Loop Top Garden Fencing Panels (Deco Promo) 4. Install new posts to specified depth (1:3 rule - posts are 1.8m and 2.4m for gate) in ground with concrete. Install fence sections, hang gate. Supply concrete, materials, etc. Please provide a brief breakdown of costs including materials. Please suggest changes/recommendations

I have 2 BFT DEIMOS Ultra BT A400 for my 2 gates of my house. And they are broken down. I need to replace 2 new one and install them. And pair each other.

Need a handyman to help me with the diy fence installation. I've all the tools and material

fence partially fall over

We need to install one pool gate to meet pool compliance requirements.

Looking for help to repair/install a lattice fence + door. There are posts already but maybe wobbly.

Looking for help to repair a brushwood fence. Dimension is 21M (length) and 1.5-1.8M (tall). We are in Wahroonga.

Looking for a carpenter to build/replace two timber gates. Dimension is 160cm wide x 80cm high (there are two existing posts). Dimension for second gate (brown one in photo) is 140cm wide (jamb to jamb) x 110cm high. Need the job done in early Oct.

I am looking at repairing the fence as few horizontal rails have been cracked. I am looking at putting some timber and nail it back. There are 2 panels.

I need someone to puppy proof our fence. There is a gap at the side and I don't know how to secure it or what materials should be used. I need someone to come and quote and explain what materials to buy so it can be done.