Find local electrical rewiring electricians in NSW

I need a qualified electrician to rewire a bathroom extraction fan.

I need a lamp rewired to Australian electrical standards. This first job is for one lamp, but I make these regularly, so this could turn into ongoing work if we’re a good fit. Also keen for your advice on best quality certified components, sockets, switches, and especially fabric or rope woven cords in specific colours, that are legal here and look good. Happy to answer questions, feel free to ask before quoting.

I have a marble base lamp that has a blown fuse. The lamp is wired through the stand and connect down through the marble base. I require an electrician to repair/replace the electrical fuses to make the lamp operation again.

I need the following floor lamp rewired as the light keeps switching on and off automatically. Seems like the connection is faulty after 4-5 years

New power cord needed on a table lamp

Looking for a licensed electrician in St Clair, NSW 2759. I have solar + battery storage and would like the controlled-load circuits checked and, moved to the main supply so they can use solar/battery power. Scope: 1. Install a Shelly Pro 4PM (supplied) 2. Connect/Control separately: - Hot water system - Pool pump - Pool heater - Air conditioner 3. Rewire the above currently on controlled load to main supply circuits 4. Supply and install contactors where required 5. Install/replace 5 additional wall switches/GPOs (supplied) Prefer the contactors sized with reasonable headroom for futureproofing. Please quote for labour, required contactors and compliance certificate (CCEW). Looking to get this completed ASAP.

Need a licensed electrician to install a new power point (GPO) in my bathroom. Looking for a safety-compliant installation suitable for bathroom zones (away from water sources, correct IP rating). Please quote for supply and installation

Knocked the glass pendant off a light fitting. Needs to be wired back in

Quote Please... I need a licensed electrician to quote for a straightforward switchboard modification at my home in Prospect (NSW 2148). I have a solar panel and battery storage system installed. Currently, my electric hot water system is wired to a separate Controlled Load 2 meter circuit, which means it cannot utilize my solar or battery power. Scope of Work: Decommission Controlled Load 2: Disconnect the electric hot water system from the dedicated Controlled Load 2 tariff circuit. Reroute to Main Grid: Reconnect the hot water system to a standard, non-controlled circuit breaker on my main household sub-board so it can draw power from my solar and battery system. Install DIN Rail Timer: Supply and install a digital DIN rail timer (or a smart relay like a Shelly) on the new hot water circuit breaker inside the switchboard. I need this programmed to strictly isolate heating times to between 10:00 AM and 2:00 PM daily to maximize solar self-consumption. Site Details:Location: Prospect, NSW 2148 Switchboard Condition: Modern/Clean (recently modified for solar/battery installation) Access: Easy access to the main switchboard and hot water unit. Please provide a fixed price quote for labor, the DIN rail timer, and compliance certificate (CCEW). Looking to get this completed as soon as possible. Thanks!

I bought this lamp in America and it's been used almost every day for six years. I've changed the bulbs once, after one got damaged in a move. I discovered this may have been quite dangerous, and supposedly the key danger point would be the electronics in the dimmer. It’s a modern lamp (from ~2019), inline dimmer in the cord, the wiring runs ~150cm through the pole of the lamp, the top unscrews, and there's two 90-degree sockets (photos attached). From what I understand, the main thing is the inline foot dimmer has to go completely. It's a 120V part and it's been sitting on 240V, so I just want it out of the circuit entirely. I'm fine for the lamp to just be on/off - no dimming. Though if the cost of a new dimmer would be immaterial, then happy to have another one. I leave the dimmer with maximum light because it’s always been a bit dim (perhaps because of the voltage), but it could just be the bulbs I’ve used. The light quality is actually perfect at present. I reckon the plan would be something like this: cut off the whole existing cord and dimmer, open up the top where the two sockets are, and test the internal wire that runs up the pole to see if the insulation is still sound. If it is just hook up a new black Australian cord and plug at the base (please note the photo of where it exits the pole). If the insulation’s stuffed it may need a new wire. I don't think it needs new sockets, the bulbs currently in use are 220 volt and working fine. Please quote for job and parts. Dimmer and complete wiring can be optional extras, or perhaps please provide a quote with different scenarios if possible. 1. New cord only 2. New cord and dimmer 3. New cord and wiring 4. New cord, wiring, and dimmer Please share a portfolio of similar cord switch outs you've done in the past. Thank you!

Rewire an old standard lamp

I have a building in Hunter Street Newcastle that needs power run to the new full ceiling. We are installing. The building is old but it is too cold and it has power but the wiring is currently old and before we rough and we need to do this job. I also need basic office lights , switches and PowerPoints supplied

Looking for a qualified electrician for general residential electrical work in a home. Jobs include installing light fittings, minor rewiring, repairs and other general electrical fixes. Must be experienced, and able to complete work safely and professionally.

I bought this table lamp in Japan but seems like that needs the socket replaced from 100V to 240V and a new Australian plug fitted.

Two lamps need to be rewired. One is floor lamp one is table lamp

Need someone to rewire phone cord for internet cord got cut

Need the existing bracket removed, remove the electrical socket and rewire the antenna connection back down to bottom of wall. Then hang TV

Electrician required - 2 visits for internal rewire + EV charger install I’m looking for a licensed electrician for two separate visits as part of renovation works. Visit 1 - required tomorrow • Disconnect and make safe all wiring in wall being removed (lighting switches and power points). 2 light switches need removal and coping, as well as 2 PowerPoint. It impacts 2 bedrooms. • Isolate and cap off as required for demolition • Re-route existing wiring to a new temporary or final location so power and lighting remain functional Visit 2 - scheduled next week as soon as EV charger delivery is received • Install new lighting switches • Install new power points in updated locations • install EV vehicle charger at side of house Additional notes • Residential property • Wall being removed is internal and not load bearing • Must be licensed and insured • Please confirm availability for tomorrow for Visit 1

Needing a licensed electrician to conduct an on-site assessment for the feasibility of a rewiring and installation of kitchen appliances for an upcoming renovation project

Old house, fully renovated, rewire 5 rooms, 2 bathrooms, kitchen and get power to the front boundary for a motorised gate