Find a reliable cooktop installation and repair service in SA

Install cooktop No silicone needed Supply flexihose

Cooktech make dual hot plate one coil is burn need to change

Opening for both is the same. Licensed electrician required.

Require removal and disposal of existing unit and install of new Bellini BGT705X Existing cutout is slightly larger than that required by new, with lip covering gap, so should be relatively straight forward. Perhaps a small wedge/filler would be beneficial. Existing Cutout: 615 x 485 (Chef 121GGW) New cutout: 552 x 470 (Bellini BGT705X) new unit dimensions 680 x 500. Install desired before May 31st Please google 'Bellini BGT705X' if you wish to review the install instructions. I've attached a picture from the install guide of the existing unit if helpful. Please advise if any questions.

Assembling new cooktop Bosch type . The person should have license

Assembling new cooktop Bosch type . The person should have license

Need an Electrician to replace an existing Stove top that has caused a trip to the Smart Meter and Install a new one correctly. Stove top ceramic 90 cms. Happy to be quoted with or without the stove top.

My parents have a new induction cooktop to replace their current so it is a cooktop swap from the old one to a new one. Current one is wired into the switchboard (32A) which is enough for the new cooktop (according to the box)

Looking for someone experienced with laminate benchtop / burn mark repairs to provide a quote based on attached photos. There is a burn/scorch mark next to the cooktop that needs repairing or improving cosmetically. Please let me know: - whether this can be repaired - recommended repair method - and your estimated cost The listed budget is just to post the task and discuss quotes — happy to negotiate based on repair approach and experience.

Gas connection in the kitchen but not used since it’s been changed to electric. But I want to change it back to gas. I will provide the cooktop. I want someone to connect the gas back

I need a licensed electrician to install 1 new induction cooktop and 1 new underbench electric oven at my home in Athelstone SA 5076. This is a hard-wired installation. I would like the electrician to first inspect my existing wiring and setup, as I am not sure whether the current cable, breaker, circuit or isolator meet current requirements. As shown in the photo, the existing wiring appears to come out from an internal brick wall partition as one brown cable, then goes into a junction box, where it is split into two white cables. One white cable is connected to the old cooktop and the other is connected to the old oven. Please let me know whether this existing setup can still be used, or whether any upgrade, new circuit, isolator or other electrical work is required before installation. Please provide a quote for labour and any extra materials separately. Licensed electrician only. Invoice and certificate of compliance required.

Hi, I’ve got a new 60cm induction cooktop arriving on Tuesday next week (replacing an existing electric cooktop). Bench cutout is standard. Thank you

Staff removed the knobs from the cooktop to clean and are unable to get them back on. Several staff have tried to no avail.

Need bellini cooktop installation of wiring to the mains by electrician. Thanks

replace thermocouple on smeg cooktop

Gas cooktop has been disconnected due to a leaking hose. Job needed is SUPPLY & INSTALLATION OF NEW STAINLESS STEEL GAS HOSE.

Old cooktop is obove the oven on the work bench. It is about 25 years old. The exhaust fan is same age. I want to replace them both.

My stow cooktop need to replaced with new stow cooktop. Please help me with this and if you need more info please pm me. Thanks

We're seeking an electrician to replace a damaged cooktop with a similar cooktop. We will supply supply thr cooktop. Scope of works: Remove the damaged cooktop Install the new cooktop Dispose off th3 damaged cooktop Cleanup upon completion

It's a long shot. I know this is a tricky thing to do. We need to expand our cooktop cutout by a few mm. Has anyone got the necessary gear to get this done for us?