Find a reliable appliance technician in Mill Park

Doesn’t work. Unsure how to connect it.

The gas heater stopped working. We are unsure as to how to fix it.

I need a licensed gas fitter to inspect and, if required, repair or replace faulty sections of the gas pipework in my home (Mill Park – Dunlop Crescent). A pressure test was done and there was a pressure drop, but the exact location of the leak has not been identified. I need the following: 1) A proper step-by-step isolation test to locate the exact leak 2) Clear identification of where the leak is coming from 3) If the leak is minor/local, repair or replace only the affected section 4) If pipe replacement is needed, please provide a detailed quote for ONLY the faulty sections (not the whole system) 5) Safety test and compliance documentation after the work is completed Please include: - Your call-out fee + cost for the leak test - Estimated cost for repair or replacement (itemised) - Confirmation that you are a licensed gas fitter Not urgent, but I want the job done properly and transparently.

One of the knobs in the Tudor Romeo gas cooktop is not working.

I need a plumber to install a new benchtop dishwasher. this is not a replacement. It is a new installation that requires plumbing work. Cabinet work will be done prior to the plumbing work. Please refer to the screenshot showing the existing water pipes under the kitchen sink. The new dishwasher will be installed in the space where the drawers are currently located

I am looking for an experienced person who can do required preparatory work to fit a benchtop dishwasher. I haven't bought a dishwasher yet. But product dimensions are included in the screenshot. I want to remove the drawers and install the benchtop dishwasher in that space. I have measured the area and confirmed there is enough space once all drawers are removed. Any required holes between cabinets for pipes will also need to be made at the same time

Handle on oven door ( one side ) now need someone to attach the door as well .

I will need assistance installing a new rubber seal for my AEG washing machine (model LF6E8431A)and to place back the door. The old rubber seal has already been removed.

Error code E2, Water inlet malfunction Bellini dishwasher

Remove old Dishlex dishwasher and install new Westinghouse dishwasher. The new Dishwasher needs to be picked from Harvey Norman Thomastown

Roller shuttles not going up or down

Install 2x Reolink POE security cameras (supplied) under an eave. You’ll need to insert some noggin timber behind the eave plaster to support the weight. Install 1x Reolink POE door bell (supplied) Ive got cat6 cable, terminations etc also supplied. I will setup and integrate the cameras. Handover will be verification that the runs test OK.

need to connect masport bbq to gas with gas conversion kit

Gas pipe connection to kitchen cooktop. To replace existing electric cooktop.

Need help repairing my washing machine. It has water leakage, and I’ve also noticed some oil leaking from the bottom. When it runs, especially during the spin cycle, it makes a very loud noise.

I need a qualified electrician familiar with installation of Tesla wall connector (Gen 3) . I have put photos showing my switch board and the distance. FYI I have solar system as well if relevant. Pls send me your offers and earliest availability as I need it as soon as possible. Thx PS: I haven't bought the wall connector yet, if you can provide it (less than $720 from Bunnings), that would be great. Pls advise when quoting. Thx

Its a small cut out. 560cm by 477cm. Unit will have a depth of 480mm but benchtop isn't stone. Have been told it can work.

Seeking a qualified and licensed plumber to relocate existing gas and water pipes in a residential kitchen. The modification range is within 50 cm from the current positions.

I want to service my sawing machine as its jammed.

I have a reolink NVR with 8 POE cameras as pictured, looking for someone to do the install at the house .It's double storey as pictured. You would need to mount the cameras, adjust the viewing angle, run all ethernet cables to a central location, and from there, a single cable to the NBN router.