Find a reliable appliance technician in West Adelaide

Need an experienced handyman to fit and install a Bosch SMS6HAI02A dishwasher under a kitchen benchtop in Beverley. The plumbing is ready for installation but dishwasher won't fit under cabinet for a few millimetres. And when the top comes off it leaves a large gap at the top, even after raising the feet. Also need to clean up hose cutout. I made a rough cutout in the cabinet side wall for the hose pass-through. Please file/clean up the rough particleboard edges and apply iron-on melamine tape or rubber edge trim to neatly cover the exposed wood core.

French Door fridge - doors don’t easily finishing closing and it’s constantly left open. New base hinges I’m assuming needed, to facilitate the final stages of closing, need someone who knows more about this to fix. Fisher & Paykel 569L French Door Refrigerator RF610ADX5 From the research I’ve done: F&P part # FP875834 for standard cams or kit 847788P Hinge cam Genuine replacement hinge kit (Part #837048, 837049, or 847788P)

Hi there, The top shelve in our Fridge freezer doesnt seem to be cooling properly. Its cold inside but it seems its only doing 50% of the job. Need assistant to figure out why. Please see photo of Fridge, make and model

I need to connect to a gas heater new one to an existing existing connection in my living room. The pipe at the moment is capped and closed so it just needs to be connected to the new appliance.

Need help cleaning mould from rubber seal in a front load washing machine

Change fridge door hinges on Haier hrf520bs from right hand to left hand and re-locate wiring as required. Hinges supplied. Qualified/insured fridge mechanic / electrician / appliance repairer preferred

The cooling has been reduced.

Need ducting run for a rangehood in a kitchen we are renovating, either through an external wall or through the roof.

Disconnect a Washing Machine & install at new location Pickup location: Mansfield Park SA 5012, Australia Drop-off location: Fitzroy SA 5082, Australia Removals size: A few items Stairs: No

I think the Bias Spring 68 - 424346 | Fisher & Paykel definitely needs replacing but maybe the balancing struts might (suspension) need replacing as well.

Hi, I need a licensed electrician to install a new electric under-bench oven at my home in Ridleyton. To make this a quick and straightforward job for you, I have already completed the unboxing and removal work. Current Status: • The old Miele oven has already been uninstalled and pulled out of the cavity. • I believe the previous setup was a direct hardwired connection. • The new replacement is an ALDI Stirling 80L Built-In Oven, which I believe comes pre-fitted with a 15-amp power plug. What I think needs to be done: 1. Convert the existing hardwired wall connection inside the cavity into a 15-amp surface socket (power point). 2. Test the line/isolation switch. 3. Slide the new Stirling oven into the vacant under-bench space and secure it to the cabinetry frame. 4. Test the unit to ensure it powers on correctly. 5. Issue an electronic Certificate of Compliance (eCoC) as required by SA regulations.

I have Electric oven that needs a new thermal overtemp fuse that needs to be fixed i have attached a photo that shows you what fuse to get and the price

The oven at the property is not heating up. The fan is running and the red indicator light comes on, but there is no heat at all. The oven is a Chef fan-forced model, EOC624S*49. Looking for a qualified technician to inspect and repair it.

The hot water tap that connects to the washing machine has always leaked. We’ve tried changing the tap but it still seems to seep water at quite a steady rate. We need someone to diagnose and fix the issue.

Nordictrack treadmill service

We need to have someone handy with tools go on-site to change out a frame section of an electric bed. Have a video instruction on how to complete this job. Tools needed are a screwdriver and a spanner. This is a simple unbolt-and-rebolt job; the timeframe should be 1 hour to complete.

Photo attached. Kitchen renovation needing the gas pipe cut back and capped. Will require some excavation of the brick wall (double brick with cavity) Then capping with 15mm bpress gas cap + testing the gas line with just a couple photos of holding pressure. Don't need the wall patched. I'm a plumber just in Melbourne and can't get to it in time for the cabinet maker. Would appreciate the help on this one. It's in Hilton an empty house.

Require a license professional to safely disconnect and remove Rennai 2001 Flued gas heater from living room.

Disconnection of built in 60cm oven (8 years old) - it doesn’t have a wall plug, it is wired in and goes to a cabling loom. Install new 60cm oven in place (also hardwired) New oven is Westinghouse WVE6516SD.

I have a new 10kg washing machine that needs levelling as it's moving when spinning. Someone that is fit as it's super heavy to pull in/out of the space it's in.