Find a reliable appliance technician in West Adelaide

Like yo like rangehood replacement.

Internal + external clean needed

Need to replace switch box for the electric recliner. Nick Scali Lounge. Faulty buttons don't work anymore. Can provide part or if cheaper price supplied by person fixing. $150 is for the labour, and I buy the part or if easier part bought by the installer. Potential to take the section of lounge to installer however I believe it is a very quick job to swap the button box. So maybe easier to have swapped at my house. Open to offers.

Need service done on dishwasher

I need support for my uncle, he is disability. He needs to assembly new washing machine and lift it on pedestal raiser.

Westinghouse easycare 500 inverter 8kg wwf8024m5wa Change over rubber

Hi, I’m looking to replace my old 60cm rangehood, as the fan is no longer working. I’m looking for supply and installation of a suitable new rangehood. Please see the attached photos of the existing rangehood and setup. Just a note: the fan is not working. If it can be repaired, that would be fine. Otherwise, I’m looking for a suitable replacement and installation.

Hi, I need help connecting my new dishwasher. The previous dishwasher was already connected and working, and has simply been removed/disconnected. The existing water supply, drain connection and plumbing are all in place. I just need the new dishwasher connected to the existing connections and checked to make sure everything is working properly.

I need a new westighouse dishwasher to be installed.

My fridge is a big by 3-4 inches in width and would not fit in the Fridge cavity provided, so need that fixing

Need to assembly and installation of a washing machine. This job require to lift and install it.

The dishwasher looks like now it is not draining properly after finishing the cycle, so I believe it may using the dirty water for the next cycle, which results the dishes comes out unwashed.

Have purchased new blades for Victa 18" Classic 500E but having trouble removing existing blades. Require removal of existing and installation new blades (provided) There is some petrol in tank so unsure if needs to be drained first (to tip on side etc) New blades are Victa CA09506B. Pls hit me up if any questions.

I’m looking for qualified tradespeople to remove an existing Rinnai gas heater and replace it with a built-in electric fireplace at my home. The existing gas heater is approximately 910 mm wide × 650 mm high. Photos can be provided. The job would ideally include: -Safe disconnection and capping of the existing gas supply by a licensed gas fitter -Removal and disposal of the existing Rinnai gas heater -Supply and installation of a built-in electric fireplace with realistic flame effect -Any required electrical work/power connection by a licensed electrician -Necessary modification of the existing opening/wall to accommodate the new fireplace -Making good/plastering and neat finishing around the new fireplace -Testing and commissioning of the installation -Relevant compliance certificates for gas/electrical work -I am open to recommendations regarding the brand and model of electric fireplace suitable for the existing space. When quoting, please specify: -Brand and model of the electric fireplace you recommend -Fireplace dimensions and heating capacity -Price of the fireplace -Labour/installation costs -Whether gas disconnection, electrical work, removal/disposal and wall finishing are included -Any items that are not included in your price I am looking for a good-quality, modern electric fireplace rather than a basic electric wall heater. Licensed and insured tradespeople only, please.

Photo attached. Kitchen renovation needing the gas pipe cut back and capped. Will require some excavation of the brick wall (double brick with cavity) Then capping with 15mm bpress gas cap + testing the gas line with just a couple photos of holding pressure. Don't need the wall patched. I'm a plumber just in Melbourne and can't get to it in time for the cabinet maker. Would appreciate the help on this one. It's in Hilton an empty house.

Require a license professional to safely disconnect and remove Rennai 2001 Flued gas heater from living room.

Disconnection of built in 60cm oven (8 years old) - it doesn’t have a wall plug, it is wired in and goes to a cabling loom. Install new 60cm oven in place (also hardwired) New oven is Westinghouse WVE6516SD.

I have a new 10kg washing machine that needs levelling as it's moving when spinning. Someone that is fit as it's super heavy to pull in/out of the space it's in.

Fix washing line It’s already set up just needs some extra work I’ll pay for the bolts that need to be fixed on top of the 50