Hire a trusted gas stove repair and installation service in Melbourne

Hello! I'm looking for a licensed plumber/gas fitter to disconnect a two-burner gas cooktop, sink and tap, then return to reconnect everything once I've installed a new kitchen benchtop. I am located in quite a large apartment building in the Melbourne CBD

Task Summary: I need a licensed gas fitter / gas plumber to replace the thermocouple on the front-left wok burner of my 90cm Smeg freestanding cooker (Model: BA9066XS) in Brunswick East. The Issue: The wok burner ignites fine, but the flame turns off immediately as soon as the control knob is released. I have already cleaned the thermocouple tip and checked the knob clearance, so the internal flame failure safety device (thermocouple) likely needs to be replaced. Scope of Work: Supply (or source/fit) and install a compatible replacement thermocouple for a Smeg BA9066XS wok burner. Important Requirements: Must be a licensed Gas Fitter / Gas Plumber (VBA registered/licensed or equivalent state certification).

Hi, I’m looking for a qualified technician to inspect and repair two issues with my gas cooktop and kitchen rangehood. 1. Gas Cooktop Ignition Issue * The ignition on the largest gas burner is not working. * The other three smaller burners are working perfectly. * Only the ignition on the largest burner needs to be inspected and repaired. 2. Rangehood Exhaust Fan Issue * Fan speed settings 1, 2, and 3 are not working. * Only the highest fan speed is functioning properly. * The fan controls need to be inspected and repaired. Location: Melbourne, VIC 3000 (Vision). I’m looking for an experienced technician who can diagnose and repair both issues. Please provide a quote, including call-out fees, labour, and any potential replacement parts. Thank you

**LICENSED GASFITTER REQUIRED | ABBOTSFORD VIC 3067** Looking for a licensed gasfitter for an urgent inspection of our existing gas cooktop. **Job details:** - Cooktop generally works well. - Some burners occasionally fail to ignite. - Faint gas smell noticed around the gas connection. - Require leak testing, connection inspection, ignition repairs and full safety check. Please email your call-out fee, approximate service/repair costs and earliest availability. Priority is ensuring the connection and appliance are safe. **NO PHONE CALLS, PLEASE. EMAIL ONLY. We will only respond to emailed enquiries and quotes.**

Current basin mounted on mdf cavity to be replaced with ikea vanity unit Current old blanco gas cooktop replaced with haier gas cooktop Please give quote for full scope. Thanks. At CBD near flagstaff. Prefer to get this done Tuesday AM or Wednesday AM

I need a licensed gas fitter to install a new 60cm 4 burner gas cooktop. The cooktop is already purchased and on site (Esatto ECG604WS from Bunnings, natural gas, cutout 560 x 490mm, manual in the box). It replaces an existing Electrolux 60cm induction cooktop and fits the same benchtop cutout. - Existing gas supply is capped off in the cabinet under the sink (from a previous gas cooktop). Photo attached. - Remove the induction cooktop and fit the gas cooktop into the existing cutout. - Connect gas, leak test and commission all burners. - The induction cooktop is hardwired, so it needs to be safely disconnected, and the gas cooktop's electronic ignition needs a 240V power point under the bench. Please confirm if you can do the electrical part or if an electrician is needed. - Provide a Victorian Compliance Certificate on completion. Please include your Victorian gasfitting licence number in your offer. Payment through Airtasker only. Please only offer if you can arrive on time with all tools, including a gas tester. Photos attached.

My gas stovetop (Smeg 4 burner) keeps igniting /sparking even though I’m not pressing down the knob. Flames lights if gas is let through. I have switched off of the electrical plug to stop the clicking for now. I was using 2 burners, then tried to turn on a 3rd when the continuous clicking happened.

My Smeg gas cooktop has developed an ignition fault. The igniters keep clicking continuously, even when the burners are switched off. The clicking stops when the electrical power is disconnected but resumes when switched back on. Looking for an experienced, qualified appliance technician familiar with Smeg gas cooktops to diagnose and repair the fault, including possible ignition switches or spark generator issues.

Disconnect gas cooktop and permanently cap the gas line. Electric stove will be installed in its place.

We have purchased a new gas cooktop to replace our existing one. My husband would like to do as much of the installation as legally permitted to keep costs down. We need a licensed gasfitter to advise on the installation, complete all required gas work, test the cooktop and provide the required compliance certificate. Please quote for your call-out, assistance, testing and certification, and let us know your availability. Location: South Melbourne.

I have 2 gas stove burners needing attention: • 1 burner ignites but produces no flame • 1 burner does not work at all I require a diagnosis and written quote/report before proceeding with repairs. I'm not based in Melbourne, so you will need to liaise directly with my property manager to arrange a suitable time with the tenants. They are usually very flexible and easy to coordinate with. Must be a licensed gas fitter and able to provide a professional quote/report after inspection.

Remove existing Gas Cooktop and Install new Miele Gas Cooktop We believe the Cutout is the same size on existing granite bench top. Miele model: KM 362-1 G (https://www.thegoodguys.com.au/miele-59cm-4-burner-gas-cooktop-stainless-steel-km-362-1-g) Location is in St Kilda East/Balaclava

One of the Gas stove burners is not igniting. Attached are images.

We need help with the replacement of gas stove , gas stove will be provided

Gas cooktop not igniting as per photo , 1 not working can hear lighting sound, need to hold it for using. Need a repair

Name- Highland cooktop 85 x 40 cm..HT3SSN/L!! No electronic ignition ,middle burner flames out upon release of the knob. Replacement Parts or similar maybe required. Person must be knowledgeable regarding the cooktop.

Re : The Gas stove ( Kleenmaid) The ignition doesn’t make a sparking noise. However, the gas works perfectly fine on all four burners.

Existing gas cooktop removed and disconnected. Need new one installed.

Need kitchen sink, gas cooktop and tap disconnected for kitchen demolition and complete removal. Need them all completely removed to within wall cavity. Please note that gas has been fully disconnected from the property, so there is actually no gas running to the cooktop. It just needs to be removed to any point within the wall.

About to purchase a gas stove top and need a qualified gas plumber to install it.