Find a reliable appliance technician in Chatswood

It does not wash the dishes. Just showing like the picture below. Please help!!!

Assemble 4 chairs and 2 coffee tables Instal washing machine

Hi there, I have more than 20 x Makita HR2630 or HR 2670 Rotary hammer needed to be repaired. Some of them have no reaction after connecting with power, and some of them are bent at the chuck which make it hard for drill bit to insert. You could check how many of them are easy to repair and I am happy to pay for unit rate

I have a bank of skylights (see photo) at high level that need sync'ing to 2 new remotes. (original remotes had battery leak and no longer work). They are quite high up so need someone that knows what they are doing. Also have another at normal height in a bedroom that also needs syncing.

Opened the panel to check whether belt was in tact or whether it was the start capacitor. Can see a line where the belt should be. Was overloaded so could be the capacitor

I've fitted a new induction cooktop and I need an electrician to run a 32A dedicated circuit with an isolation switch please. Full brick, double storey house.

Rewire a line for electric lawnmower. 5min job. Max. https://youtu.be/2UQg65POmQQ?si=R9SAFSIBLPP7Gn_D

Both freezing and refrigration layers are not cold inside.

Microwave not turning on, tried resetting the switch but didn’t work. Not sure what’s causing the issue.

House, easy street parking. 1 * old floor gas bayonet heating fitting/socket is not working properly. Supply and install a new working bayonet socket. Gas tightness test after installation to ensure everything is safe and fully operational.

House, easy street parking. Removal of two unused gas bayonet heating sockets (not used for years and no longer required). Removal of accessible under-house bayonet gas heating copper pipes and deletion of the tees. Installation of new copper material to re-join the copper line as a straight run. Perform a gas tightness test after work is complete to ensure no gas leaks and that the remaining gas system is safe and fully operational.

My Breville Dual Boiler coffee machine isn’t producing any steam out of the steam wand. Everything else works fine. I have cleaned the steam tip holes so there isn’t any blockages. I suspect it is a broken o-ring inside the machine that is leaking or causing pressure issues. When I turn the knob for the steam, no steam comes out anymore. Can’t run descaling process either as the machine short-circuits, so there probably is an internal leak. Looking for a fix for this issue.

Replacing a Smeg rangehood. The power and exhaust is already in place. Need to drill 4 10mm holes in ceasarstone to hang the rangehood. Also, to measure the placement of the rangehood so it fits nicely with the top of the bulk head.

I need some help in removing the styrofoam Under the fridge (new)

Dryer is not working… may be the belt, machine has been taken apart already

The house has gas connected already. I need a new gas point for a bbq, about 14 meters length with copper, under the house with 1m clearance. I need an quote with a plumbing licence number Need to be done this week

This is a gas heater outlet in our lounge room in a bulding of 1970 can you just remove it. We dont need it anymore. Just remove it and seal it.

Need to install a 60cm ducted rangehood. Remove old rangehood.

Have a new 7 room partition of office 45 sqm and want to have each room have ducted vent. Right now the current setup only has 2 vents. Would like someone to come out and view current setup and quote on next steps to having each room comfortably ducted. Happy to pay for the quote and consultation in good faith

Stove top degrease, range hood, remove cobwebs, full vacuum throughout. 8.30pm - View all the details of this offer: https://www.airtasker.com/offers/01K9KGDX7VANEA7KFRBE635MR7