Find a reliable appliance technician in Baulkham Hills & Hawkesbury

Fix my Washing Machine, Not draining

Microwave is not heating the contents inside

We have installed a new 60cm rangehood. It has both recirculation and ducted options. Currently it's installed to operate in recirculation mode. We would like to convert it to ducted. Range hood doesn't need to be removed. Only ducting in required.

Take out the existing dishwasher and take it away

Looking for a licensed and experienced gas fitter to assist with a new gas connection at a residential property in Kellyville, NSW. Must be able to provide valid ABN/ACN and gas fitting license for the application process with Jemena for gas connection to property. Once the gas pipeline is installed from the street to the property by Jemena, connect the gas cooktop to the gas meter. Ensure all work is compliant with NSW safety and installation standards. Requirements: Must be fully licensed and insured. Able to issue a compliance certificate upon completion.

My dishwasher lock might broken, the door cannot be closed. Is anyone knows how to replace a new lock? Thanks

I have a heat pump dryer that needs to be installed in the laundry room - right hand side of the washing machine. Unfortunately the dryer is a little bit too wide (around 10mm) so need to cut the cabinet back a little for it to fit. Job includes connecting the dryer to existing power (behind the washing machine) and connecting its drain hose into existing plumbing underneath the sink (next to the washing machine)

Washing machine door seal and hose needs replacement

Connecting and repairing and replacing water housing into dishwasher and also connecting inlet water housing for washing machine

Hit yellow gas pipe and need it fixed today

Connect a Bosch front loader washing machine. - Remove transportation screws - Position Machine - Connect water pipe, waste pipe and power

Hi I would like to get my Tesla Wall Charger Gen 3 installed next to my main switchboard. It is single phase and has a solar system (only 2kw system). Let me know if you need any further information Cheers Mazz

change BBQ natural gas line back to LPG I have the LPG and Natural gas kit with me

Supply and replace oven switch mech and install power point - View all the details of this offer: https://www.airtasker.com/offers/01JQ6CE678RA88KCNJ38XTJXVH

Fixing the kitchen drawer Fixing the screw of the dishwasher Fixing the kitchen cupboard strip Touch up of cupboard

Activate the gas connection for heating by placing the socket on an existing connection outlet. Note: gas connectioniw there and no new pipes required . Pictures attached of inside and outside of the wall. Outside wall needs to have the same oulet/ socket as the inside one.

fault finding install GPO for dishwasher and washer install switch for garden light install garden lights replace ceiling fan - View all the details of this offer: https://www.airtasker.com/offers/01JPNHF7TMYFN25GY46F06TRJE

I need someone to set up our multi gym equipment for home. It is: CORTEX SM25 Multi Gym (Dual Stack Functional Trainer, Smith Machine, Half Rack) Link: https://www.lifespanfitness.com.au/products/cortex-sm-25-6-in-1-power-rack-with-smith-cable-machine

I have an Ethernet cable already run through and up the walls and now wrapped around a truss. It is easy to access cable in my roof with standing height. Cable simply needs to be ran 6-7m to the front eave where it needs to be pulled through and have the Ethernet rj45 patched. I’ll install my camera myself at a later date. I’ve done all this work before for my other cameras and have all the equipment so I’m just putting it out there to see if anyone will do the work this time as I am busy this weekend with other jobs . Ladder already in place to access roof. Max 1 hr job for anyone competent with a fishing/trace wire.

I have a CAT5 cable tucked into the brickwork at the front door for a doorbell to be installed however I am not able to trace it back to the Hills home hub in the garage as there are 4 ports inside the house with 4 wired on the switch and the door bell being the 5th. I would need the one end crimped with a head, the traces to the switch in the home hub and drill mounting holes for the doorbell. Reolink POE doorbell and TP Link 2.5G POE+ Injector purchased.