Find a reliable appliance technician in Cherrybrook

I need an experienced handyman, carpenter, or kitchen installer to mount a new plug-in Omega ORU70XL undermount rangehood into an existing cabinet slot and install a fresh ducting run. The old Omega P780 has already been completely removed and the area is clear.Power: No electrician needed. The new unit is plug-in, and a standard power socket is already active inside the cupboard.Cabinet Modification. Ducting & Materials (Tasker to Supply): We have the new rangehood, but you will need to supply the installation materials. Please include the cost of a 150mm flexible ducting kit and a new 150mm external wall vent/louvre in your quote.The Job: Route the new 150mm ducting from the top of the rangehood through the to the existing external wall exit point.

Need assistance with choice of range hood and installation for my new outdoor bbq area. Corrugated iron roof above the outdoor area Ceiling height is 2300cm and bbq surface is 90cm off ground (1400mm gap between bbq surface and roof) Cost is for installation and help with choice of range hood (will pay separately for the purchase of the range hood)

Looking for someone to convert our range hood from recirculating to external venting. Ducting will likely need to run through the roof and vent outside.

I have a Fisher and Paykel Washing Machine and I need he door seal to be replaced. I already have the part.

Need a washing machine technician to repair washing machines and dryers.

Unit is approximately 1.5 years old imported rangehood. Lights and display are working normally. Fan stopped working after switching from Speed 1 to Speed 2 for about 2 mins. ES error displayed. After power reset, fan does not start at any speed. No motor noise or movement. Looking for someone experienced with appliance electronics, rangehood motors or control boards. Please advise: • Diagnostic fee • Experience with imported Chinese appliances • Availability

Hi I need to install a small cabinet drawer above the oven. Please see the attached screenshot; as you can see, there is space above the oven where I want to place this cabinet drawer. Kind regards Jay

Need a handyman/plumber to install a mini washing machine on top of a laundry benchtop. Scope of work: • Cut/drill holes through a stone-look benchtop for water supply and drain hoses. • Connect the washing machine to existing water and waste plumbing under the laundry sink. • Ensure all connections are secure and leak-free. • Experience working with stone/composite benchtops preferred.

The issue with the ASKO dishwasher is that the middle and top drawers are not cleaning properly. See the attached picture. Thanks Jay

Persistent gas smell coming from inside a Bosch freestanding gas stove I checked the external gas connections with soapy water and could not find any visible leaks. The smell seems to be coming from inside the appliance rather than the external pipe connection Would like a licensed gas fitter / gas appliance technician to inspect the stove and internal gas connections for possible leak or valve issue.

We recently capped off an existing gas line to our outdoor area as we were in the process of enclosing it with an aluminium door and windows. Now I'm after a licensed plumber to reinstall a gas bayonet in the same space on the wall. Please refer to the pictures or happy for you to come out and view the job. Thanks

Licensed gas fitter to service our BBQ which is on mains gas

Escea gas fire no apparent problems . Some coals have soot onbut not been serviced for ten years. Also need a safety check on a rinae gas heater

The dishwasher is functioning, but it is not cleaning the dishes properly.

Pressure washer will not turn on.

The toy car is not switching on. I have the charger but it doesn't seem to be charging properly as it doesn't turn on.

The dishwasher is leaking when it is doing the wash job

Replace a gas stove with a new gas stove of same size (60cm) and connect it up to the gas.

Looking for a licensed electrician (preferably with ABN) to install a power point underneath my stove so the gas stove ignitor can be plugged in and start working. Currently the ignitor isn’t working as there is no power outlet in that space. 3 photos attached to show the setup and help understand the job. Please quote if you: Are a certified/licensed electrician Have an ABN and can provide an invoice Can bring the required materials for installation

I need an experienced appliance technician to inspect and repair my Eureka E10s robot vacuum. The vacuum repeatedly turns in one direction and cannot move in a straight line. The app shows a “wheel slipping” error. What I’ve already done: • Cleaned both drive wheels thoroughly • Checked for hair/debris obstruction • Reset the unit • Rebuilt the map • Tested on dry tile and carpet The issue persists, so it may be a wheel motor or sensor fault. Looking for someone who: • Has experience repairing robot vacuums or small appliances • Can diagnose wheel motor/sensor issues • Can advise on parts required if replacement is needed