Hire trusted appliance installation services in Parramatta

1. Uninstall the existing hardwired 60cm oven 2. Install a new 60cm hardwired oven.

I need a handyman to install a new rangehood.

I’m looking for an experienced handyman or electrician to install a ducted rangehood. The rangehood comes with the mounting bracket and only needs to be fixed into place with two screws. The main work required is: * Replace or repair the drywall behind the rangehood * Install the rangehood onto the supplied bracket * Run the ducting through the ceiling * Vent it either through the eaves or the roof Looking for someone who has experience with rangehood ducting and can complete the job properly for a reasonable price. Please send through your quote and availability.

Looking for a licensed electrician to replace my existing induction cooktop with a new one. It's a straight swap — same size cutout, so no cabinetry or benchtop cutting needed. Both old and new cooktops are hardwired (not plug-in), so I need someone qualified to disconnect the old one and wire in the new one safely. What's needed: Disconnect and remove old induction cooktop Install and hardwire new induction cooktop Test it's working safely I'll have the new cooktop on site, ready to go. Just need the swap done.

Gas stove appliance knob doesn't click and turn on the flame. New knob available

need a vent installed for the Simpson 4kg vented dryer. The dryer is wall mounted. I will supply the vent kit. Need the dryer to be taken down, vent kit fixed and the duct exhaust to be installed to the brick veneer external wall. Need to cut a hole in the brick veneer wall. The dryer is less than 500ml from the external wall, so the ducting is very short, straight out from the dryer exhaust outlet. Need to hang back the dryer on the wall once the job is done.

Need to install a rangehood . I have already got the new rangehood need to replace the old one

I would to install new rangehood and all connections already exist from old rangehood which has been removed

Cut hole on metal roof on commercial building to install a range hood cowling and duct

Commercial Kitchen Exhaust Hood Installation I need an experienced commercial kitchen exhaust installer to provide a quote and inspect the site. Scope of work: * Supply and install two commercial exhaust canopies, each approximately 1.5 metres long. * Connect both canopies into a shared ducting system. * Ensure installation complies with Australian Standards and local council requirements. * Advise on any required make-up air, exhaust fan, roof penetration, fire safety, or compliance requirements. * Site inspection required before finalising the scope and quotation. At this stage, I am looking for: * An initial price estimate. * Availability to attend the site for inspection and discussion. Please provide: * Estimated cost range. * Earliest inspection date available.

Removal 2 rusted bolts as shown in picture and installation of 2 burners to replace existing bolt

Replace broken cooktop for a new glass cooktop 70 cm supply and install. Disposal of the old unit. Need to provide cooktop brand, model name, and have normal warranty.

Remove old cook top and install new electric cooktop. Take the old one for recycling.

I need someone to install an electric cooktop. And if they can recommend a cooktop I can buy from them. 52 x 59 cm

I need a slimline rangehood installed over a gas stove. Some cabinetry will be required for the rangehood to attach to and to sit in and align with existing cabinetry. I will purchase the rangehood and have it ready for installation. It will not require ducting.

Removal of old pull-out kitchen range-hood and installation of new one

I currently have an Esatto EUM52 (52cm under-cupboard rangehood) installed, and I would like to replace it with a Westinghouse 52cm integrated rangehood (WRI515SC). I have already purchased the new unit. It is mostly plug-and-play, but some minor adjustments are required. The installer will need to: Trim about 5 mm at the back Trim about 2 mm on the side MDF panels This will require basic carpentry work (cutting/chiselling the cabinet panels).

Modify existing washing machine waste to accommodate two washing machines and 1 dryer

Installation of force usa c10 all in one

I have two newly built kitchens. I need the most budget recirculating rangehood supplied and installed. The cooktop will be two burner electric stovetop plug in. One is lower floor and other is second floor.