Hire trusted appliance installation services in Parramatta

Remove old aircon and dispose of it Install new aircon and test and commission and fill with gas, include full cost of labour and material material except aircon machine will be provided by us 5.2kw kogan machine

Need someone with experience and license to install 145cm rangehood in new takeaway shop in wentworthville.

Site visit and quote for commercial electrical upgrade $50. I need a licensed electrician to install two new dedicated circuits for a commercial food stall in Harris Park. The existing setup (one 10A outlet) is insufficient for the equipment load. ​The equipment includes: ​1 x Acai Softserve Machine (10A / approx. 2400W continuous). ​1 x Gelato Display Unit (195W). ​1 x 256L Chest Freezer (170W). ​Requirements: ​Circuit 1: A dedicated 10A (or 15A) weatherproof outlet for the Acai machine. ​Circuit 2: A 10A double weatherproof outlet on a separate circuit for the freezer and gelato display. ​All work must be compliant with AS/NZS 3000 and include RCD (Safety Switch) protection.

Install new dishwasher, cut caninets , connect pipes, install a mew electric board and install dishwasher

Need to install washing machine and dryer. Dryer to be installed on top of washing machine with a bracket

Replace broken cooktop for a new glass cooktop 70 cm supply and install. Disposal of the old unit. Need to provide cooktop brand, model name, and have normal warranty.

I have a full CCTV system including: 4 existing wired security cameras, a DVR/NVR recorder and hard drive. The cameras are already installed on the house exterior. I need a technician to: • Supply and run new cables neatly back to the recorder • Reconnect all existing cameras properly • Set up the recorder and make sure all cameras display correctly • Help set up remote viewing on my mobile phone House has two levels, however all CCTV installation work is required on the ground floor only. One cable (backyard)run may be approximately 30 metres.others (in front of the house)are much shorter. Looking for a reliable and affordable installer with CCTV experience. Please provide a total quote (including cables) and confirm availability. Location: Constitution Hill, NSW.

Hi, I need someone to Install a Hoselink (Evolve) Hose Reel on a brick wall. I’m not sure where to put it, I have attached a picture with the tap marked with a red circle, and possible locations marked 1 and 2. Let me know your thoughts. I’m looking specifically for someone who has installed one of these before and give me the right advice about where to mount it. Please show examples of previous jobs like this. Thanks!

I have recently relocated. So, need help with getting the washing machine set up in the unit.

Hi I need a Drivevision front dashcam installed with the hardwire kit into the fusebox. Need the wiring to be neatly concealed. This will be installed in a 2023 Hyundai i30 sedan.

I need to install an oven(bottom section) and takeaway the old one.

Remove existing Rangehood and install a 60cm slide out Rangehood. Must have tools and experience

Need a integrated fridge and freezer installed along with a dishwasher. Already in place , just need the panels installed and adjusted

Replace existing slide out range hood with a new one, I already have the new one here. Must be experienced licensed and insured please

Help install the rangehood provided and dispose the old one.

I need a skilled handy person who can install a security latch and viewfinder to my front door. Need to ensure centred

I’m looking for an experienced handyman or automotive fitter to install a rear roller shutter cover (automatic remote-controlled) on my BYD Shark 6. ✅ What’s provided: • Brand new remote-control roller shutter kit (imported from China) • All brackets, fittings, and wiring included • Basic installation guide (in Chinese – I can assist with translation if needed) ✅ What needs to be done: • Remove any existing fittings (if necessary) • Correctly align and securely fit the roller shutter unit • Connect and test the automatic motorized system so the remote control works smoothly • Ensure proper sealing and waterproofing around the edges • Confirm the shutter locks and unlocks properly ✅ Requirements: • Experience with installing automatic ute roller shutters, tonneau covers, or similar vehicle accessories • Ability to handle basic electrical wiring for the motorized unit (connect to power source if required) • Bring your own tools (drill, rivet gun, hand tools, etc.) • Must work carefully to avoid scratching the vehicle • Ideally, have a second person to help with lifting/positioning (I can assist if needed) 💰 Budget: $400 (negotiable if extra work is required) 📍 Location: Lidcombe, NSW 🗓 When: Flexible – can be done any day/time that suits

Need to replace rubber seal on front loader washing machine Will need the replacement seal and installation