Find a professional heating and cooling technician in West Sussex

Hi, I’m looking to swap my Nest Learning Thermostat 3rd Generation for a Nest Learning Thermostat E and would like to split my radiators back into two separate heating zones: upstairs and downstairs. The heating was previously set up in two zones, but one radiator was connected incorrectly, so I ended up combining everything onto one thermostat. My current Nest 3rd Gen thermostat is now having software issues, and I need to return it. I’d like to install the Nest Thermostat E and restore the two-zone setup, with separate controls for upstairs and downstairs. Could anyone advise me on whether this is possible and what would be needed to get it set up correctly? As i am having combi boiler and 3 generation nest is not very useful for me . Thanks in advance!

Replace our faulty Honeywell ST699 with a new boiler programmer. Please supply and fit appropriate 2 channel replacement. Some trimming of the wall tiles may be required to fit the new unit depending on size.

set up a nest link, will need to pull power from a nearby socket but the boilder is already wired.

We would like to replace the thermostat receiver for a Google nest with the receiver for a Honeywell T3R Wireless programmable thermostat, for our Worcester greenstar combi boiler. The receiver should replace our current one and the tasker should ensure that the receiver and thermostat are fully synchronised and functioning as expected.

Business address requires AC unit fixing. Issue identified as PCB board replacement. U4 error code.

have a GoodHome portable air conditioning unit that requires diagnosis and repair. The unit still cools the room effectively, but as soon as the compressor kicks in it develops a loud rattling noise. We’ve had to place something underneath the right-hand side of the unit to reduce the vibration, which helps slightly, but it’s not a proper fix. I suspect it may be something relatively straightforward, such as loose mounting bolts, a loose bracket or casing, worn anti-vibration mounts, or a component that requires adjustment. I’d like someone to inspect the unit, identify the cause of the rattling, and provide a quote for repair. Ideally, I’m looking for someone with experience repairing portable air conditioning units rather than installing fixed systems.

Largeish popcorn maker has internal light and heating plate, mechanical stirrer and heating pot with three separate switches one for each function. Everything working apart from the heating pot which isn't getting hot.

plummer to: 1. move a dinning room radiator ( same wall, but to the oposite corner) i will provide a new radiator and make sure full access to the radiator is possible the bar counter in the picture will come out before) 2. replace 4 valves on 2 x bathroom radiators

Electric Underfloor heating in basement stopped working. V cold floor tiles ☹️

I need a qualified engineer to service my boiler

Oven not heating up properly

Boiler showing fault code F9 and low pressure

Nest battery does not seem to be charging and I've been unable to connect it my Wi-Fi for a couple of years.

Underfloor heating. Manifold and pump are hot but the pipes under the floor are not heating up. In tre picture some zones are not connected but I don’t need these anyway. It’s just two zones and they are cold. The electrical NuHeat box in the picture is functioning

Hi, our boiler says low water pressure. Usually I twist the knobs underneath and it repressurises but it isn't working. Need help as I am abroad and my lodger is struggling to get it to work/to get the pressure back up. We are on Caledonian Road, Chichester

No hot water in the immersion heater

I have an ideal logic combi boiler in my new house and what I believe to be it's original electronic thermostat. The two do not seem to be communicating with each other, the heating is always on despite what is set on the thermostat. Can anyone help?

Quote for prep floor, lay insulation boards, lay electric under floor heating, cover with self leveling compound, lay LVT click system In Hall and Kitchen approximately 15.5 square meters of LVT and about 13.5 square meters of underfloor heating .

Need to install a mixer tap for the downstairs W/C and also fix the hot water pipe by replacing it and connecting the same. Material costs can be additional to the budget.

Thermostatic Shower connect Leaking Fitting Change