Find a local heated floor installer near you

Need a few jobs done. - Need a boiler service, - Investigate - Underfloor heating, doesn’t seem to have as much output as it could - New a tap installed in an upstairs bathroom

Looking for an electrician to swap out two old Ambiente thermostats on a wet underfloor heating system. I’m supplying the replacements (Heatmiser NeoStat V3). Straightforward like-for-like swap with no rewiring needed.

I have an old and faulty actuator for my boiler/underfloor heating systems that needs to be replaced. I'm holding the new one in my hand, it needs to be installed onto a brass body and also its electrical wires need to be connected to the green connector on the bottom right hand side of the picture

Looking for an experienced underfloor heating specialist, ideally someone who has worked with older Uponor C-56 wireless control systems. The controller serves three wireless room thermostats, none of which are communicating with it. Engineers have already attempted a reset, tested a replacement antenna and tried pairing a new thermostat, all unsuccessfully. The controller still activates individual heating zones during its normal 10-minute manual test cycle. Specifically looking for someone to diagnose the fault and repair the existing controller if possible, or recommend and install a compatible replacement control system while retaining the existing manifold and pipework. Please only respond if you have experience with Uponor or similar wireless underfloor heating systems. Located in Clapham SW4. Initial budget is for diagnosis and possible minor repair; replacement parts and installation to be quoted separately.

One of our thermostats for the underfloor heating broke, I tried to change it but now all the thermostats have no problem. No fuse switched off

2 of 4 circuits not heating and return manifold is cold

I need to set up some tado x thermostats 8 zones I already have wireless tado x thermostat and receive to turn on and off hot water and underfloor heating, but zones not configured. Also underfloor heating has cold zones that I need fixed

fix my floor heating， it’s making some wired noise, the pressure is fine

Fit winder underfloor heating

The entire flat is using the under floor wet heating. The old thermostat is broken. Model number: UFHDIALB I ordered the same replacement. Need to replace it and seal with silicone to make it looks nice. I am available from 7pm on Wednesday. Please let me know your availability. And or if you need more information. Thx

To check all connections to the boiler/wiring centre and thermostats and commission our underfloor heating.

Plumber to finish installing the underfloor heating manifolds

We wish to install underground floor heat in our new house in SW12 0DR. Need to set up in the living room and 4 bedrooms. What is the timeline? We have not moved in yet. We have not moved in yet. This gives us planning the time to move in.

existing grouting old, dirty and chipped there is underfloor electric heating to be aware of need old grout removed and replaced in room 7ft x 9ft less bath/washbasin, cupboard and loo

I need PIR insulation laid down, Fastwarm Wet underfloor heating installed, and a screed poured in. This is for a good sized kitchen (not more than 30sqm). It has to be done this Friday, the kitchen is being installed on Saturday.

Kitchen floor to be fully re-tiled with electric under floor heating

Install 20 square metres of WUNDA 20mm Rapid Response underfloor heating system. Ground floor kitchen, small toilet and landing. Concrete floor, that has been levelled.

I need someone to install underfloor heating along all of ground d floor, price is not fixed as person would need to come and view in person to provide accurate quote

I’m looking for an experienced tiler or underfloor heating installer to complete my electric underfloor heating installation. What’s already done: * Electric heating cable has already been installed and tested. * Floor sensor is already in place. * All materials are supplied. Work required: * Secure the heating cable/mat where required. * Connect the heating cable to the mat as per the manufacturer’s instructions. * Apply primer if required. * Pour and level approximately 10mm of self-levelling compound suitable for electric underfloor heating. * Leave the floor smooth, level and ready for tiling. Requirements: * Experience installing electric underfloor heating systems. * Experience using self-levelling compounds. * Must have your own tools. * Please provide photos of similar work you’ve completed. Important: * All materials are provided. * The heating cable has already been tested and must not be cut or damaged. * Please only apply if you have experience with electric underfloor heating installations.

Room Details: Kitchen size: 5.16m (L) × 3.15m (W) Current floor: tiled Issue: mixed subfloor (concrete + timber) ❗ Current Problem: Half of the kitchen floor sits on concrete Other half sits on timber subfloor Timber section is now damaged/uneven Ant infestation has occurred from edges (likely via gaps under timber section) Some tiles are already lifting/damaged 🔨 Scope of Work Required: 1. Strip Out Remove all existing floor tiles Remove timber subfloor section completely 2. Subfloor Correction Replace removed timber area with solid concrete base Ensure entire floor is level across full 5.16m × 3.15m Apply suitable damp-proof membrane (if required) Ensure no gaps/entry points (fully sealed against pests) 3. Floor Preparation Apply self-levelling compound across entire floor (if needed) Prepare surface suitable for large-format tiles 4. Electric Underfloor Heating Supply and install electric underfloor heating system Include: Heating mat/cable Insulation boards (if required) Thermostat (preferably smart programmable) Must be compatible with tile finish 5. Tiling Install large format tiles (likely 1000x1000mm or 1200x1200mm) Full kitchen area to be tiled (under cabinets where possible or up to plinth – confirm approach) Ensure: Correct adhesive for large format tiles Minimal lippage (flat finish) Clean grout lines Include tile layout planning (centred preferred) 6. Finishing Grouting Silicone sealing around edges and units Ensure fully sealed floor (no pest entry points)