Find a local heated floor installer in London

2 of 4 circuits not heating and return manifold is cold

I need to set up some tado x thermostats 8 zones I already have wireless tado x thermostat and receive to turn on and off hot water and underfloor heating, but zones not configured. Also underfloor heating has cold zones that I need fixed

fix my floor heating， it’s making some wired noise, the pressure is fine

The entire flat is using the under floor wet heating. The old thermostat is broken. Model number: UFHDIALB I ordered the same replacement. Need to replace it and seal with silicone to make it looks nice. I am available from 7pm on Wednesday. Please let me know your availability. And or if you need more information. Thx

To check all connections to the boiler/wiring centre and thermostats and commission our underfloor heating.

Plumber to finish installing the underfloor heating manifolds

We wish to install underground floor heat in our new house in SW12 0DR. Need to set up in the living room and 4 bedrooms. What is the timeline? We have not moved in yet. We have not moved in yet. This gives us planning the time to move in.

Install 20 square metres of WUNDA 20mm Rapid Response underfloor heating system. Ground floor kitchen, small toilet and landing. Concrete floor, that has been levelled.

I need someone to install underfloor heating along all of ground d floor, price is not fixed as person would need to come and view in person to provide accurate quote

I’m looking for an experienced tiler or underfloor heating installer to complete my electric underfloor heating installation. What’s already done: * Electric heating cable has already been installed and tested. * Floor sensor is already in place. * All materials are supplied. Work required: * Secure the heating cable/mat where required. * Connect the heating cable to the mat as per the manufacturer’s instructions. * Apply primer if required. * Pour and level approximately 10mm of self-levelling compound suitable for electric underfloor heating. * Leave the floor smooth, level and ready for tiling. Requirements: * Experience installing electric underfloor heating systems. * Experience using self-levelling compounds. * Must have your own tools. * Please provide photos of similar work you’ve completed. Important: * All materials are provided. * The heating cable has already been tested and must not be cut or damaged. * Please only apply if you have experience with electric underfloor heating installations.

Room Details: Kitchen size: 5.16m (L) × 3.15m (W) Current floor: tiled Issue: mixed subfloor (concrete + timber) ❗ Current Problem: Half of the kitchen floor sits on concrete Other half sits on timber subfloor Timber section is now damaged/uneven Ant infestation has occurred from edges (likely via gaps under timber section) Some tiles are already lifting/damaged 🔨 Scope of Work Required: 1. Strip Out Remove all existing floor tiles Remove timber subfloor section completely 2. Subfloor Correction Replace removed timber area with solid concrete base Ensure entire floor is level across full 5.16m × 3.15m Apply suitable damp-proof membrane (if required) Ensure no gaps/entry points (fully sealed against pests) 3. Floor Preparation Apply self-levelling compound across entire floor (if needed) Prepare surface suitable for large-format tiles 4. Electric Underfloor Heating Supply and install electric underfloor heating system Include: Heating mat/cable Insulation boards (if required) Thermostat (preferably smart programmable) Must be compatible with tile finish 5. Tiling Install large format tiles (likely 1000x1000mm or 1200x1200mm) Full kitchen area to be tiled (under cabinets where possible or up to plinth – confirm approach) Ensure: Correct adhesive for large format tiles Minimal lippage (flat finish) Clean grout lines Include tile layout planning (centred preferred) 6. Finishing Grouting Silicone sealing around edges and units Ensure fully sealed floor (no pest entry points)

I need a cable installed for my underfloor heating mat in my shower room. Picture 1: shows the plug socket in the adjacent room, which I’m hoping you can run the cable from. Picture 2: shows the direction of the joists under the floor to help plan the route. Picture 3: shows the height where I need the cable brought up to feed through the wall so the thermostat can be installed on the other side. There is lots of room under the floor to pull the cable through

1) Carefully remove all floorboards downstairs and set aside. 2) install timber battens between joists 3) install rigid insulation minimum 50mm thick between floor joist, above battens. 4) underfloor heating pipework installed between joists (materials supplied by us). Joists to be notched where required to allow pipework to pass through 5) dry sand a cement mix screed to the placed between joists above underfloor heating pipework and levelled flat. 6) fix down floorboards over the top of all, fixing floorboards into the joists.

Hi looking for a labour quote to fit retrofit underfloor water based heating on the floorplan attached excluding WC and utility room. The existing flooring is laminate/carpet on suspended wood/concrete. Scope of work will require existing floor removal and prep, installation of ufh and also laying laminate on top. Thanks Peri

Take up existing floorboards, batten out between joists and apply insulation, install UFH between insulation and dry screed layer and fix back down floorboards

Wunda water underfloor heating

I have heatmiser underfloor heating one zone receiver come on but no heat provided

Underfloor heating in one room is not working. Floors stayed cold, control panels are all working fine. Boiler is only a year old and just had its annual service done, pressure is good and have nothing wrong.

Underfloor heating has been laid out on the ground floor of the house from corridor to through lounge. I need the downstairs area to be screeded before the flooring can go on. Open to offers/ suggestions.

Thermostat shows as heating active but not heating from mat