20 Dryer technicians in London

Tumble dryer is not working and need someone to fix it. BEKO brand dryer

Hi I need someone to help disconnect my old washer dryer, connect new one and take old one down to bin cupboard from 2nd to ground floor with lift.

My washer dryer doesn't start. It used to work very well without issues for nearly 3 years. For the last 2 days it doesn't seem to switch on even though I see the yellow light lighting on.

Our washer dryer stops on the 15mins of cycle. It wash perfectly as it always been before, however when I add drying it stops after 15 mins. Even if you only put 30 mins, it stops on the 15th. Model Samsung Eco Bubble WD90J6410AX/EU. After the drying stops the machine is completely cool, which should be hot...

Hoover WDYN 9646 G-80 Dynamic 9 +6 washer dryer. The machine has stopped working, it made a noise and now it won't drain the water in the drum. The water flow from the sink is slow.

Hoover WDYN 9646 G-80 Dynamic 9 +6 washer dryer. the machine made a noise and now it won't drain the water. The lights at the front of the machine keep flickering.

I need someone to install a new Indesit washer/dryer model IWDD 7143. Also to remove the old washing machine, which has been disconnected.

both appliances need looking at washing machine will only run on economy 20 min wash, any other cycle and it wont stop running even after hours tumble dryer also not working keeps stopping and takes 5 hours to dry clothes!

I had a condenser tumble dryer delivered. It requires no assembly or installation other than it being plugged in. I want to place it inside a cupboard inside which there is a washing machine and stack it on top of the washing machine. There is an electrical outlet with a single cord which is currently used by the washing machine. It has to be replaced by a new plug with two sockets. Then the tumble dryer has to be stacked on top of the washing machine and be plugged in.

Hotpoint was her dryer not working

Fix handle to dryer - needs new mountain pillars to attach the new handle

I have an InDesit WIDL126. The machine does not fill up with any water and it does not spin. When I open the box on the side where the detergent goes, the section for pre-wash fills with water, but no water flows into the section designated for the actual wash. When the machine runs, it sounds like it's operating because it goes through the entire washing cycle but like I mentioned no water fills up the machine and it does not spin.

machine turns on and displays time but counts down while nothing happens. Pump is clean and drum is not stuck (moves manually) so i suspect blocked hose? i am not strong enough to move the machine and check. could be something different but assuming it needs new hose woudl like full quote to come out and replace. it's an indesit washer/dryer

Dryer has stopped working, but washing cycle works fine. Need repair.

Just to supply and change Dryer belt

A new tumble dryer to be installed and to be placed on top of washer. There is also a minor job like mounting the tv stand under the flat panel.

Belt has come of or broken from hoover washer dryer

Bosch dishwasher is stuck on the clear water button and unable to use it. Hotpoint tumble dryer - Think the door catch is broke so will not start

The handle to the door of my Bosch dryer has come off meaning that I can no longer open the dryer. It needs drilling back on I think

Tasks: 1. Change three light fittings 2. Install a Brita kitchen tap 3. Install a new washer dryer (AO delivery man said we need a cold water feed, something else I'm not too sure, however, I have attached the pictures for the washer dryer) 4. Vacuum cable rewiring (it only works in specific angle) picture attached 5. Shelves Part 1- A solid pine shelf needs to fixed into a built in cupboard. (It has been cut to size but might need slightly making smaller) (To match other shelves ideally to be fixed to the wall with wooden blocks screwed to wall. (Picture attached)) Part 2- Three shelves which is already now fixed in the cupboard need small triangular extensions added to them which have been cut to size. And the edges need to be filled with gripfill or something similar. You MUST: Must be responsible and able to attention to details. I need the jobs to be done nicely with details been takes care. Time: 25th Jan 3:00pm (if possible)