Find a professional awning contractor in South Brisbane

Hi there, my second storey metal awning has been wrecked from the winds and half of it has come off (see photos) I'd like some one to remove it and take the scrap away. It's fairly high up, around~7m and hoping it is not too much of an issue. Also the aluminnium panels are fairly long and would need to cut/folded before scraping. Budget is very flexible as my insurance provider needs me to remove asap. Thank you!

I bought the plastic awning from Bunnings which needs to be installed outside of the mantionry wall. I don’t have the drill bit as the hole needs to be drilled to 95mm deep with 10mm diameter drill

Need the awning dismantled leave material on site it doesn’t have to be removed and can be damaged don’t need to be careful

I have a job on today where I need an offsider to hold one end of a roller shutter awning. We will be on ladders with planks going across. You don’t need to be able to use tools or anything, just be able to hold one end of the roller shutter whilst I fix it in place, There are 2 awnings to fit.

Affix awning to side of house (see images for location on house) I have put together the pieces of the awning however require assistance to finish this process and to affix

We put these plastic/perspex awnings up but had to shift one higher so it cleared the door. We'd like the bigger one to be the same height as the smaller one. It's probably about a 30 minute job. This might be a 2 or 3 person job due to the size - it's not heavy, it's just a bit awkward as the middle bracket isn't screwed in and can come apart if not supported. I can help to hold the middle up if this will be easier for you. Ideally the old holes will be filled and the slight gap from the top of the awning to the wall sealed.

The metal cover of one of our queenslander house windows needs replacement.

Garden shed, window Awning, gas bottle cover installation

Garden shed installation, window awning shade installation, Gas bottle covering sheet installation

Assistance to remove and replace an existing exterior awning - comfortable on ladders and moderately heavy lift. Approx 2hrs work

I need two exterior jobs completed: Awnings – 4 polycarbonate awnings (approx. 5.5 kg each, flat-packed). Brackets and fixings supplied. Each awning needs to be assembled and installed on an exterior fibre cement wall. Work involves constructing the awnings, locating studs, drilling through fibre cement, and securely fixing into studs. Aircon duct cover – The plastic cover protecting outdoor aircon pipes/cables (approx. 2–3 m) needs replacing. Old cover removed, new ducting fitted. Either supply new ducting (reimbursed) or advise me what size to purchase. Requirements: Must have own ladder and tools (drill, stud finder, etc.) Experience with exterior handyman/awning or aircon work preferred Seal holes as needed for weatherproofing. Access: Ladder required for both tasks.

Two powder coated, square-tubed triangular framed window awnings clad with FC, painted and installed on BCorp premises. The awnings are to go beside and match the existing. 25mm square tubes. One awning will need to dog leg over an exterior light fitting. I have the specified paint. the price is negotiable

duplicate metal framed awnings including cladding and painting. colourmatched to existing and installed

The roller awning (447cm wide) on our Leader Gold caravan is flaking off, and we would like it replaced - we are looking for someone to buy a replacement awning, remove the old one, install the new one, and take away the old one

duplicate metal framed awnings including painting

mount a kings awning to arb roof rack

Remove the last two slats from awning from high set house - neds a long ladder

Attach a framed awning/cover onto the wall to cover a solar inverter. Has about 4 bolts to fix the unit.

I purchased an awning online, 5m long. I need to install it to attach at rear of my home outdoor. I need to ensure after installation it is stable and will not leak water in with the holes drilled.

remove 2.5 awnings + its control panel and wires, seal the holes, take away the 3 awnings (1 awning has been partially removed)