Find professional local plasterers in Inner West Sydney

Hi there, I’m looking for a handyman/builder to build a gyprock partition wall to divide a large room and create a smaller room. The wall will be approximately 3570 mm long and 3500 mm high. Please let me know if you’re interested and available. Thanks.

Fix with a new gyprock after removing damaged section. I will sand and paint

gyprock plasterboard or villaboard. Seal old chimney hole. Photos attached . Handyman. Carpenter. . Burwood. . Please note only need to seal the triangle shape hole. Not the whole wall. .

Fix a hole in ceiling. See photos.

Our soundbar was previously wall-mounted beneath the TV but came loose after being pulled by our kids, leaving damage and holes in the plasterboard. Looking for someone to patch and repair the damaged area, securely remount the soundbar using appropriate wall anchors or studs, and tidy the cables. Please bring the required tools and mounting hardware.

Gyprock plaster to seal old chimney hole. Photos attached

I have two Timber Line timber shelves (80cm long, approximately 28cm deep). These must be installed using the manufacturer's concealed floating bracket system. No visible L-brackets or external supports. The wall is gyprock. Installer must have experience locating studs and/or using appropriate structural fixings for floating timber shelves. Please only make an offer if you have installed this type of shelf before.

We need an experienced plasterer to finish our hallway (pictures attached). We are looking for a layer of Bondcrete/Cemstik over the existing lime plaster, followed by two/three skim coats of lightweight plaster (gypsum/aggregate etc. Open to material suggestions that you are used to working with). The area is approx 6500x1300 x3000 height. It doesn’t require any work over the door areas and would likely only need one coat of plaster where we have retained plaster (see pictures) for consistency. Finished with sanding also required.

wall to be plaster new acrylic render.

I have two TVs that need wall mounting on plasterboard walls and cables run internally in each wall to entertainments units. 1) LG 65 inch G6 OLED - I have the LG wall mount plate and TV bracket kit. I installed the wall plate securely but had some issues with the bracket with the supplied LG anchors pushing into the wall cavity. Needs a fresh install. There is a timber stud the middle of where the TV needs to hang. There is brick in one section of the wall approximately 40mm behind the plasterboard. In other sections just plasterboard and some conduit and other wires behind to avoid. Wall cut out required to run the cables into TV unit (power, several HDMIs) 2) Samsung 55 inch QLED - To be mounted on plasterboard wall. I have the wall mount kit. Wall cut out required to run cable into TV unit. This TV has a Samsung One Connect box so only a small wall cut out and single cable run needed. Photos attached of both TVs, walls I need them mounted on, and wall mount kits.

just repairs a hole in the wall and repaint

We have had a washing machine installed upstairs (due to young kids) and need some small gyprocking done and painting. These holes are quite small. The larger hole we require a paintable access panel installed so we can access the plumbing in the event of a leak. The access panel is about 450 x 400. The 2 holes in the wardrobe one needs plaster and the one needs gyprock from a cut hole from plumber, both are small. We want all the 3 painted if required (Not sure if the access panel will fix exactly or need some gyprocking.

We’re looking for a plasterer to do some patching and skim coating.

Patch hole on ceiling must be available tomorrow

I need around 3.5 metres of cornice fitted , I have already got the cornice

Need ceiling fan cutout patched sanded and painted with ceiling white. I have the gyprock cutout so no need to supply. Also have a couple small holes that just need patch no paint.

Had to relocate a light switch and power point so need holes patched. Also had to relocate and LED light on ceiling so need hole patched.

3 small drywall patches where paint and paper face have been pulled off, exposing gypsum core. Torn paper edges need trimming, filling, and the wall has a fine stipple texture that needs to be matched before repainting. Rental inspection on Friday the 24th of April - need it done ASAP.

Gyprocker needed to install 1 Wall 3.5m wide 2.8m height No cornice Studs Aquacheck plasterboard Tape joints Plaster Sand Situation: Current wall is brick render. Has rising damp. Want to attach new wall with studs.

I’ve already run all the Cat6 cables through the ceiling to the exact AP locations. I need someone to mount two Ubiquiti access points on a gyprock ceiling (approx 600g each). Proper ceiling-rated anchors or fixing into timber will be required — the included plastic plugs aren’t suitable. I also need one external Ubiquiti access point mounted on a masonry wall. The cable is already in the ceiling above that location and can drop straight down behind the unit. No cabling work required — just mounting and securing the three APs. photos show the two ceilings and one external wall