Find a professional outdoor blinds contractor in QLD

Outdoor blind 2nd story installation on the balcony 3m by 2.4 I have blind

I need an outdoor blind installed - outside kitchen window.

Looking for someone experienced with masonry/concrete fixing to install 3 Coolaroo crank-operated outdoor blinds on an apartment balcony. Blinds are: * 2 x 2.4m wide * 1 x 3.0m wide Installation is into the concrete ceiling/soffit. Access is straightforward from the balcony and no working at heights equipment should be required. Would require proper plugs and screws given wind affected area The two 2.4m blinds are going side-by-side across an opening that is approximately 4.8m overall. With the end brackets/fittings, the combined width appears to be closer to 4.94m, so I suspect the blind rode may need to be carefully trimmed/cut down slightly to fit correctly. Need someone who: * Has their own rotary hammer/masonry drill and concrete fixings * Is confident accurately measuring and installing the brackets * Can assess whether the two 2.4m blinds can/should be shortened and carry this out if required * Can install all three blinds level, secure and operating properly * Ideally has experience installing outdoor blinds/awnings into concrete All blinds are onsite and ready to go.

Hi we are a home improvement company looking for an experienced installer to come onboard and assist us with our roller shutter, plantation shutter and outdoor blind installation jobs. We have a good volume of jobs to install and it will be ongoing work in Brisbane, Gold Coast and country areas. We pay good rates and also will have consistent work ongoing in a great team and work environment thank you

Wanting to put temporary outdoor window blinds on 4 of our 2nd story widows on townhouse. We are renting and in very thin budget. Any help or guidance much appreciated.

install 4 outdoor blinds to lowset house windows

Replace outdoor blind and repair leak on patio roof and leak near skylight

Install outdoor blinds x 12 -14

Remove x2 outdoor blinds located on front deck before painter completes work next week.

Outdoor blinds does not roll Up as usual

Ww have an outdoor motorised blind that is not working. The motor runs when I press the remote, but one out of 4 won't lift. The remote model is AC123-06D, which I believe is an Alpha motor. We are located in Norman Park.

To install few outdoor plastic roller blinds, drill into wooden beams.

I have two outdoor blinds that I need installed. They are going on windows and will be attached to brickwork. 210x240 and 240x240

Outdoor blinds for splashback window and patio (measure and quote only)

The tensioning wire on this outdoor blind has separated from its fixing on one side. I do not know if there is a piece missing. I have two other blinds that are intact, but would benefit from tensioning being increased.

i need help with outdoor blinds installation.

my outdoor blinds has come off the rollers. I need someone to put it back on

I have 2 outdoor blinds to that need to be hung. See photos

I need someone urgently to cut down 4 x Stratco Ambient outdoor blind cassette/headboxes / blind components. Installation is already arranged. This task is for the cutting only. The blinds have been supplied slightly too large / too tight for the reveal openings. Stratco has advised that the manufacturer can speak directly with the person doing the cut to guide the process if required. Approximate cuts required: - Blind 1 / left side: received cassette/headbox 2986 mm. Requested adjusted length 2976 mm. Approx. 10 mm cut. - Blind 2 / front left: received cassette/headbox 4005 mm. Requested adjusted length 3996 mm. Approx. 9 mm cut. - Blind 3 / front right: received cassette/headbox 2949 mm. Requested adjusted length 2941 mm. Approx. 8 mm cut. - Blind 4 / right side: received cassette/headbox 2989 mm. Requested adjusted length 2979 mm. Approx. 10 mm cut. The cuts need to be accurate and clean. Please only apply if you have the right tools and experience cutting aluminium or similar blind/awning components. Important: - Final measurements must be checked before cutting. - No cutting should occur until the final cut measurements are confirmed. - Stratco/the manufacturer can speak with you before cutting if needed. - I can provide photos and the measurement table. - I can potentially bring the blinds to your workshop if that makes the job easier. - Job is urgent. Please include in your offer whether you have experience cutting aluminium cassette/headbox, awning, or blind components.

Install 2x outdoor blinds in alfresco area