583 Gate Installation Experts in VIC

I need a gate built to block off a section of my backyard. Opening is about 1.5mt wide so gate/fence will fit in this area. Would like it to be 1.5mt width x 1.5mt height.

Need to hang a gate between house and carport to stop dogs getting through and same at the side of the house so they can run through to front. 78 cm-1m gate. Access required 6ft side of house. Access not required

As one of the remote controllers was lost, we need to recode the receiver to prevent the lost controller from opening the gate. The receiver is from Automatic Gates, and the model is RX-2 or IK324.

It's a glass pool fence. Pool gate, on the latch side is rubbing against adjacent glass panel at the top corner. Panel on the hinge side is also tilting and not plumb.

Current gate closes shut, but doesn't lock. Barrel need replacing with new keys.

Garage gate have not been serviced for about 3+ years. Still funcitons fine but can hear squeeks and rattles Did check out the franchised websites to get a feel for price, but from experience (ie plumbing), they say a base rate then hit you up 3-4 folds on additions if required. Open to any mornings or afternoons post 3pm. Weekend would be great too The price i put is just an indication and welcome your quotes and whats covered.

A driveway gate post is rotted and needs replacing. The [Content Moderated] .1m post is concreted in very well and needs a jackhammer to get it out. The new post and replacement bags of concrete are already on site ready to go, the post just needs cutting to size and the checkouts for the cross rails cut out. It's very important the new post is concreted in properly - no short cuts. Min 500mm deep, 150mm diameter around it. Only need the post concreted in, the driveway gate will be rehung later after the concrete sets.

Fence gate is sagging, so hinges on gate need adjustment or replaced

i want to install a side gate _timber 1.2 width 1.8 height as soon as possible.

Just need someone with the right tools who can cut 2 old thick screws out of a gate bracket. Requires metal saw and strong hammer. Photos as below. Day/date is flexible.

Need someone to fix the fence and install plinth at the bottom. It has tilted towards left. Pictures attached. Got some bigger jobs as well. Decking, painting and gardening.

The upper hinge has rusted and snapped off, will need to be rewelded

The hinge on our garden gate has snapped off. It either needs to be welded back together, or a replacement hinge added.

My front gate needs to be adjusted and moved up in my fence post. Essentially I need someone with a power tool who will also provide some sound advice to make it easier to open my front gate.

Hi there - i need to replace my old picket front fence in Yarraville with a new woven wire fence. The length is no more than 20m. I also interested in getting 2 pedestrian gates and a small car gate (~2m wide) included in the same style. Many thanks, Tom

Please read carefully. Need job done by Feb 2020 or earlier. Building permit is required. See attached elevation and plan. Following are requested by structural engineer report: 1) Wall footing: 500 WIDE x 450 MIN. DEEP STRIP FOOTING WITH 5-L12TM or 5-N12 BARS TOP & BOTTOM. LOCALLY WIDEN FOOTING UNDER BRICKWORK. PROVIDE BLINDING CONCRETE WHERE REQUIRED. 2) Post footing: STEEL PILES MUST BE FOUNDED INTO NATURAL STIFF SOIL AND SHALL NOT BE FOUNDED/TERMINATED IN FILL. THE MINIMUM FOUNDING DEPTH SHALL BE 250 (UNO) BELOW GROUND LEVEL WHICH MAY NEED TO BE INCREASED/DEEPER TO ACHIEVE A SAFE WORKING LOAD OF 65 kN (TYPICAL) IN NATURAL SOIL. ALTERNATIVELY PILES MAY BE TERMINATED BY REFUSAL ONTO/INTO NATURAL SOLID ROCK. REFER DETAILS. IT IS RECOMMENDED THAT THE PILING CONTRACTOR UNDERTAKE TESTING TO CONFIRM PILE DEPTHS REQUIRED TO ACHIEVE DESIGN REQUIREMENTS. 3) Gate Footing: 300 WIDE x 300 MIN. DEEP TIE FOOTING WITH 3-L12TM TOP & BOTTOM. LOCALLY WIDEN FOOTING UNDER BRICKWORK.

Hey there, my name is Lucy. I need to hire a handyperson to help me in Blackburn North VIC 3130, Australia. What do you need done? Installation What is the type of property? House Which areas of the property need work? Outside What would you like the handyperson to work on? I need a handyman to adjust the hinges and/or latch for the gate. We had a new gate installed however have since concreted the driveway so the ground is now elevated (see images). One of the hinges is buried in the concrete. We also had to remove the front step (merbau) and will need it trimmed down to a new height and reinstalled. Please let me know if you have any questions.

Back gate out of alignment and not closing

1.) Need to repair the existing fencing. 2.) Dismantle and get rid of the garden shed 3.) Fix the metal gate.

Hi I’m after someone to instal 4 metal trellis stands. There is no dirt in the garden yet so you will need to dig out and concrete them in so they don’t move. They are the bunnings white steel diamond plant trainer : https://www.bunnings.com.au/whites-steel-diamond-designer-plant-trainer_p3042464 I also need some concrete installed around our gate post which is in the same area. The gate has started to move so pulling it upright and setting in concrete to help secure it. See photos.