Find a professional gate installation in Melbourne Western Suburbs

I need two timber pet gates built and installed at a rental property in Point Cook. Each gate opening is approximately: Width: approximately 1600 mm Height: approximately 800 mm Requirements: Gates are to contain a toy poodle. One side of each opening is an existing timber fence/post. The other side is a rendered/plaster wall. Minimal wall fixings preferred as this is a rental property. No posts, concrete, or supports fixed into the artificial grass. Gates to be timber construction (pine or similar economical timber, recycled). Slatted design with gaps small enough that a toy poodle cannot pass through. Gates must be adequately braced to prevent sagging. Suitable outdoor hardware, hinges and latch required. Preference for a neat, lightweight and practical solution rather than a decorative one. Please provide: Supply of materials. Construction. Installation. Photos of similar work if available. I have attached a concept sketch showing the general idea, but I am open to suggestions for the most practical design. The priority is a simple, sturdy, low-cost pet barrier. Appearance is less important than functionality and minimising damage to the rental property.

Looking for an experienced carpenter, fencing contractor or handyman to remove and replace our existing timber side gate with a new, modern and secure gate. Scope of work: Remove and dispose of the existing timber side gate. Supply and install a brand-new, modern side access gate. Preferably a solid, contemporary design with minimal gaps for privacy and security. Gate must be sturdy, weather-resistant and suitable for outdoor use. Install heavy-duty hinges and a secure locking/latching mechanism. Ensure the gate is properly aligned, opens and closes smoothly, and is securely fitted. Make any necessary adjustments to the existing gate frame or posts if required. Design preference: Open to modern aluminium, steel or quality treated timber options. Ideally looking for a clean, contemporary finish that complements the house. Please note: Photos of the existing gate are attached. Please inspect the photos and advise on the most suitable replacement. Please provide a quote including materials, labour and removal/disposal of the old gate. Please include photos of similar gates you have previously installed. Looking for someone experienced who can deliver a neat, professional and secure finish.

I need my front gate finished as previous tradie didnt complete it but took my money. Its been nearly a year and i need it completed ASAP

High winds blew our side Colorbond gate off its hinges/latches. Need a handy person or gate specialist to realign the gate and securely re-attach it to the frame/post. Please bring suitable metal screws/fixings. If hinges need replacing, please let me know or include basic hardware in your offer. Photos attached showing the full gate and hinge connection.

service both my front entry gate and automated garage door. The front gate functions normally and just needs a routine service, but the machine screen has stopped working and needs to be looked at. The garage door requires a full service, lubrication, and track inspection as it occasionally gets stuck halfway through operating and has to be re-closed.

This gate to the garden does not unlock. We have tried turning the key several times and nothing works. Need someone to take a look to fix. May need a replacement of the locking mechanism.

Provide and install 1800 tall colourbond lockable gate and return. To fit 1.9m sideway. Colour Dulux Monument.

Exposed Aggregate Concrete under clothes line and the square area outside kitchen window

I have lost the key to our electric gate box and need it opened to reprogram our remotes. Located in Sunshine North

Electronic fence gate is not closing/opening. Need help fixing

There are 4 different issues: 1. Picket fence not connected to upright post 2. Rear boundary fence falling over (base of uprights likely rotten) 3. Double gate in picket fence to be rehung with new hinges 4. Side boundary fence leaning We would like the fences fixed and where possible standing upright and reinforced

Need help to install child safety gate, half completed but won’t close. https://www.bunnings.com.au/perma-child-safety-easy-fit-baby-gate_p0095272?store=6395&gclsrc=aw.ds&gad_source=1&gad_campaignid=21122993677&gbraid=0AAAAADtbEB-3dNXh8N686YDUNC8aU61Ar&gclid=CjwKCAjwifjVBhBKEiwAYx4K9Emuz0IzEy3aL3AWcuG_vqzGvZpKXab-_qveqks2Y62C93BaiIbVHhoCudwQAvD_BwE

I started the job and stopped when I realised I shouldn't be working with chemicals while pregnant. The gate is 360cm x 190cm and needs to be oiled front and back. I have bought Cabot's brand equipment and supplies for the task, you are welcome to use this. I have already cleaned the gate with the Cabot's deck clean solution. I started taping plastic wrapping to the adjacent metal parts, but this step is incomplete. It needs more masking tape and then it will be ready to be oiled front and back.

The post re-attached to the driveway concrete, and one of the gates attached to the brick fence, Thanks

The gate need to be reinstalled as it’s removed for solar batteries installation

Replace existing side gate lock with a new same provided lock. Issue 1 - Will need drill etc as some of the existing screws on the current lock very stiff, cannot undo with screw driver ! Labour only required - 1-2 hours max.

Welds have cracked on gate need it to be welded back on and welds sprayed.

Hello, I'd like to get a basic gate installed between existing fences that have a spacing for a single car driveway. I do not have existing materials. The spacing is 2.8 metres. Maybe around 1.5 metres for the height, but I'm flexible and it definitely doesn't need to be as tall as the fence. Will need the fence for basic privacy and security purposes. It needs to be porous to wind as a previous gate failed under wind stress. The system should be able to accommodate a basic lock setup (e.g chain/latch and padlock) but I can set this up myself so it does not have to be included in this job. Open to second hand components if they do not compromise the durability of the construction and it reduces the overall cost. The existing adjacent fence posts may need reinforcement after the gate is added. A photo has been attached. It shows a former gate that is no longer there. I do not require the same design as this former gate.

15 min job need safety screens screwed to wall

After somebody with some experience in making the electric VEVOR gate motor open and close at my house, as photos indicate the motor is mounted and powered up, but I’m having trouble linking the remotes/keypad etc and the magnets which shut off the motor.