Find a professional gate installation in Inner West Sydney

I have garden metal gate that is attached with 2 screws need removed

I have two front metal gates where their hinges have rusted off and will need to be ground off (angle grinder) and welded on with new replacements. Need someone who is familiar with and has relevant tools to weld. Additionally a gate latch has been painted shut. I will need someone to strip off the paint and get it reworking, or replace latch with new one.

Replace base hinge for glass pool door. The hinge is a Fethers hinge. The door hinge appears fine, but the base floor mounted hinge has broken

Looking for someone to install 2 hardware mounted baby gates: - 1 retractable gate at bottom of stairs - 1 metal gate at top of stairs Also need someone to re-attach 2 kitchen cabinet doors. We need the job to take place tomorrow at Leichhardt at 11am. Please confirm in your offer that you are available then Thanks!

FAAC 740 failed to work, can hear the humming sound but it’s not moving. Lost the release key. The gate sometimes can be pushed manually, sometimes it’s locked dead.😵

Repair damaged brick gate pillar My mother accidentally accelerated the car into our neighbour's front gate, which has weakened the brick column supporting the metal gate. The metal gate post goes deep into the ground and is currently holding the brick column together. Without the metal post, the brick column appears to have separated horizontally and could come apart. Looking for an experienced bricklayer or handyman to inspect the damage and repair/rebuild the brick column properly. Please provide a quote for the repair.

I have a 38m common fence with my neighbour which we’d like done in colorbond + side gate.

Helping an elderly neighbour to slowly fix up their aging and weather damaged frontage. Looking for a carpenter/handyman to remove the existing narrow metal side gate and replace it with a simple, sturdy timber gate matching the basic cottage/picket style of the existing front fence. The priority is a quick, practical and cost-effective solution rather than elaborate custom joinery. Photos show the existing gate, passage and adjacent white timber fence. Scope: * Remove and dispose of existing metal gate if required. * Measure opening and fabricate/supply a timber gate to fit. * Simple vertical timber/picket construction, visually sympathetic to the existing white cottage fence. * Prefer treated pine or another economical exterior-grade timber. * Install suitable hinges and a straightforward latch. * Gate should swing freely, close securely and withstand normal outdoor exposure. * Ideally paint white to match the existing fence; alternatively quote separately for painting if cheaper for us to do ourselves. * Existing posts/walls may be used for fixing if suitable; please advise if an additional timber post is required. * No need to replace or modify the rest of the fence. Please quote an all-inclusive price for labour + material, and mention whether removal/disposal and painting are included. Happy for you to use standard off-the-shelf materials and keep the design simple to minimise cost. Timing: ASAP / flexible for someone who can fit it around another nearby job.

2 cast iron gates 1.4 x 2.00 m high

I need a gate to go across the front fence asap

I had a sliding gate installed that doesn’t work and I want to know what is wrong with it and a quote to install it properly.

Need to cut approximately 10 - 20mm of the base of this powder coated aluminium slat gate to provide sufficient clearance from path. Slats are 6cm long,x 1cm. There are 17 and they are hollow aluminium. Looking for a proper tidy job and for this to be done with a track saw with metal blade and not a grinder.

Driveway gates per photos attached to be hung to metal posts with swing motor. Please only apply if you have done this before

Woodwork over doorway 2 small picket gates 1 side gate (around 1.5 m by 1m) Stretch of picket fence approx 3m 3 small under awning wood brackets (approx 3 m off the ground) Paint supplied Need prime and two coats

We have a wooden fence that we want a gate in. Ideally we would use the current wooden fencing and turn it into a hinged or sliding gate. In addition, the ground behind the fence is slightly higher than footpath level. Will need to remove the pavers, shovel out and replace the pavers so that they are level with the footpath.

High winds broke the screws holding the Colorbond gate frame to the brick wall. The frame has dropped and the gate cannot close. Need a handyman or fencer to lift the frame back up, drill new holes, and securely re-anchor the Colorbond frame into the brick wall using heavy-duty AnkaScrews or Dynabolts.

Need to cut rusted parts off the bottom of a gate and weld a new bottom rail

I have a metal front gate. The hinge has rusted out/failed. I purchased additional hinges from Bunnings, but I don’t think the holes accurately line up for the screws. Will need someone that is able to fix/reattach. Photo is what it looks like properly attached.

Brick gate post saw cut and removed. Thickest section is 11cm. Front of house - easy access and can drive back up to it. Removal of all waste. Must be done today.

I need a custom built light, removable barrier across my hallway. No gaps and at a height of about 120 cm, to keep cats out. Made out of a light material,, easy to lift and put away when necessary. May be acrylic or plexiglass has been suggested or whatever is really light but will stay in place. No drilling, just using perhaps Velcro on the walls or L brackets was a suggestion. Or whatever is the best and easiest to takeoff and put on also needs some kind of gate through it so I can walk in and out and close behind me. I need you to come to my house and have a look at that space and take measurements to get it exactly right. Cats can get through smallest gaps, so need to really plan this out properly. Also need this to be very easily taken off and on and stored away when not needed.