Find trusted local electricians in VIC

Qualified A Grade electrician with a valid REC required to: 1) relocate/move 2 existing power points higher on the wall/plaster board, around 240mm from the floor. The power points are currently on the skirting board which will be getting replaced. 2)Install a new power point with USB C & A in another room, the closest power point to the 'new' power point is about 3m away. Must provied a COES.Note- It is an older house on stumps and is very low to the ground. Refer to circled area in the images for the ‘new’ power point locations

Trouble shooting and servicing solarium bed. Model ‘Hapro Collagen Sun 26/5’ Inconsistent distribution of power between the UV lamps. Does not appear to be a consistent flow of power being evenly distributed across the lamps top and bottom beds. Unit turns on. Unit operates as it should - face lamp switches on/off, fan turns on/off and adjusts according to the settings, timer adjusts. Just the lights flickering. Can’t upload videos here so tried to show through photos.

looking for electrician to install 1 x power point and 1 x chandelier on the ceiling. Forest Hill victoria 3131

Looking for a fully licensed electrician to do the below things. Wall Type - Standard plaster wall. Requirements: Must be a fully licensed electrician (please provide your license number when bidding or upon arrival) Please include the cost of heavy duty TV bracket, recessed TV media box, any switch board required. Must be able to provide a Certificate of Electrical Safety upon completion. Flexible with days and times for the right person. Job Details: JOB 1- Mount a new 85 inch TV, flushed to wall using a good quality mounting bracket. Concealment of wires using a recessed media box. Existing points on wall - ethernet point & dual power point at centre of wall. Towards the bottom it's a phone line & CCTV wires that feeds to DVR. TV set up - connect to DVR via hdmi, additional HDMI FOR play station. Ethernet wire to go to DVR, SOUNDBAR & SUB power supply. CCTV ups power supply. JOB 2 - FIX / REPLACE this switchboard. The broken button is for lights.

Looking for electrical work. Here is the plan for the three rooms upstairs, where most of the work is. Though in the list below there is some work in other areas such as the laundry which I’ve put a picture of too Total list of work below; ·      Install 2x smoke detectors ·       Replace 13x existing downlights to new 90mm downlights (IC-4) ·      Replace light with downlight (lounge upstairs) ·      Replace light with 2x downlight (entrance) ·      7x new GPO ·      Updating/moving GPO x8 ·      1x fan in bathroom ·   ·      1x lighting for mirror (ensuite) ·      2x sconce lighting (master) ·      Connecting lighting switches for upstairs rooms ·      Change 2x exterior lights to flood lights (we will supply light) ·      Connect existing lighting switch that was disconnected at the switch

I am converting my backyard garage into a studio and need a fully licensed and insured Electrician to complete the electrical rough-in and fit-off. Scope of work: 1) Main Cable Connection & Testing: There is an existing power cable running from the main house to the garage inside a conduit (on concrete driveway). The middle section is intact, but both ends are currently cut and bare. You will need to test the cable for insulation resistance/continuity. If safe, connect it back to the main switchboard with appropriate RCBO protection. (If the cable fails test, we can discuss a variation to pull a new cable through the existing conduit). 2) Lighting: Replace 4 existing light fittings in the garage. (I will supply the new light fittings/fixtures).3) Power Points: Supply and install 3 new double GPOs (double power points) inside the garage studio. 4) The garage walls are bricks, the wiring can be placed in a conduit and attached to the ceiling or the wall. Please provide a fixed quote including all materials (except the 4 light fittings) and labor. COES must be provided.

I need an old light fixture repaired in a rental flat. It's an old Batten Holder, I have a new B22 Batten Holder from bunnings I'd like to swap it out with.

Hi, I’m needing to change an LED downlight. I have the downlight. Should be a quick job for you. Thanks

Due to weather electrical sensor light got detached from the fascia board and is hanging down. Also some water got into the fitting and is short-circuiting if you switch it on. Need to reattach the fitting, drain the fitting and make it work

Dinning room, kitchen, main bedroom light fittings installed. External back & front lights repaired, new down lights installed in hallway

Have 2 power points behind 2 tvs that aren’t working looking to get them both fixed

Licensed Electrician Required – Tesla Charger Installation & Minor Electrical Work Single-storey home with three-phase power. Looking for a licensed electrician to complete a Tesla wall charger installation and a small number of electrical maintenance items around the home. Please provide a fixed-price quote after reviewing the photos and job details. Preference for electricians experienced with EV charger installations and able to provide all required compliance certificates. Location: Tarneit Please quote your total price and earliest availability.

Replace 4 downlights you will need a ladder. Parking is hard so im happy to pay for a parking station

Need a 20amp power point installed in a warehouse

Simply need 3 pendants replaced with new ones. Must be qualified electrician.

The alarms being replaced are Quell Q1275 240V AC interconnectable. Happy to purchase new mains powered alarms but will need help with remounting and wiring them (the old 3 pin plug on the existing ones have been discontinued)

Move PowerPoint and tv point Replace 8 downlights

I require a licensed electrician to complete the following electrical work: 1. Install Bathroom Heat/Fan/Light Unit: Supply not required – I will provide the unit. Install and connect the IXL Tastic Original 3-in-1 Bathroom Heat, Fan & Light. Replace the existing Clipsal wall switch with the appropriate wall switch that came with the unit. Existing bathroom downlights and exhaust fan functionality must be retained and continue to operate correctly after installation. No bathroom wall tiles are to be damaged, removed or broken during installation. Photos of the existing setup is attached. 2. Supply and Install Two External Downlights: Supply and install 2 new LED downlights outside the house near the left-side gate. There is an existing downlight in the area which can be used as a reference point for installation. Electrician to supply all fittings and materials required. 3. Replace Toilet Light Bulbs with Downlights: Supply and install 2 LED downlights (one in each toilet) to replace the existing light bulb fittings. Existing Clipsal wall switches are to remain in use and continue functioning normally. Electrician to supply all fittings and materials required. 4. Wiring and Electrical Work: Electrician to supply and install all wiring, connectors, cabling, mounting hardware and any other materials required to complete the works. 5. Electrical Certificate: Provide the required Electrical Safety Certificate / Certificate of Electrical Compliance upon completion of the works.

Need a licensed electrician to hard-wire a commercial Fagor gas bratt pan (Model: SB-G915IM A). Details: Existing 230V power point/isolator already installed near the machine. Bratt pan requires hard-wired electrical connection for controls/ignition. Electrical rating: 230V, Single Phase (1N), 50Hz, 0.7A. Appliance is already on site. Need connection completed and electrical box secured as per manufacturer instructions. Must test operation after connection. Must provide compliance certificate if required under Victorian regulations. Location: Collingwood VIC 3066 Please quote including labour and any small materials required (cable, glands, connectors, etc.).

Licensed electrician required to install 2 x Philips Hue Akari downlights in my Melbourne CBD apartment. Scope of works: * Remove 2 existing downlights * Enlarge existing ceiling cut-outs from approximately 63mm to 90mm * Convert existing hard-wired connections to plug-base connections suitable for the new lights * Install 2 x Philips Hue Akari downlights (lights supplied by me) * Test operation and ensure installation complies with Victorian electrical requirements Details: * Apartment with plasterboard ceiling * Existing lights are currently wired directly into the electrical circuit (not plug-based) * New lights require 90mm cut-outs and plug-base connections * Looking for a neat, professional finish with clean cut-outs and no ceiling damage * Licensed electrician only * Please include any parts required (e.g. plug bases) in your quote and advise whether a Certificate of Electrical Safety will be provided