Find trusted local electricians in Ryde

Replace an old smoke detector mounted on ceiling with a new Clipsal 240V Photoelectric Smoke alarm(CL755PSMA4), new alarm will be provided.

Need an electrician to install one power point in our family room on the wall.

Looking for someone to replace outdoor bulbs with led lights like the ones in picture. I have the lights, there are 4 of them. Currently some are light bulbs and we want them changed to the ones in the picture

Replace wall switches, switches supply included

Replace 6 Down Lights (Bottom Part Only) The lights have 2 parts, only the bottom part needs replacing.

Replacing exiting Cooktop and Oven (Whirlpool) BOSCH Series 4 60cm Electric Cooktop - PKE611BA2A BOSCH Series 2 60cm Electric Oven - HBF133BS0A Hard wired - Need Licensed Electrician I have checked sizes - They fit in existing cutout.

Hi,
I’m looking for a licensed NSW electrician to rewire my existing electric hot water system. Job details * Residential property with 3-phase power * Electric storage hot water system currently connected to Controlled Load 2 (CL2) * Disconnect from CL2 and reconnect to the main household meter / general supply * Install a dedicated hard-wired timer so the hot water system only heats between 12:00pm – 2:00pm daily * Hot water unit is a standard electric storage system (~3.6kW) Technical notes * Where possible, please allocate the hot water system to a separate or light-load phase to maintain good phase balance (EV charging, air-conditioning and kitchen loads are used during the day). Requirements * Correct circuit protection (MCB / RCD as required) * Proper switchboard labelling * Full system testing after installation * Compliance with AS/NZS 3000 (Wiring Rules) * Certificate of Compliance for Electrical Work (CCEW) must be provided upon completion, as required under NSW regulations Notes * Rewire + timer only (no new hot water system installation) * No solar PV * Easy access to both switchboard and hot water unit * Please advise if any electricity retailer or distributor notification is required after CL2 removal Please include in your offer * Confirmation you are a licensed NSW electrician * Estimated labour time * Whether the timer is included or supplied by me * Any additional parts or compliance considerations you foresee Thanks!

Supply, install 8kw Deakin FTXV80WVMA and dispose existing.

Took fitting off to clean. Can’t put it back.may need electric fittings removed to put back

Hiiii I want to install 2 ceiling lights.

New spa getting delivered Need spa PowerPoint extended from already 15amp outside PowerPoint as new spa comes with only 2.5 meter power cable Need extra 4meter extended

I need a licensed electrician to install a double power point in my apartment. The purpose is to have: • One outlet dedicated to the fridge, and • One outlet for a modem / router Currently there is only a single power point in this location, and I would like it upgraded to a double power point for safety and proper usage. The job involves replacing the existing socket and ensuring the installation is compliant with Australian electrical standards. Please quote including labour and materials. Note apartment is an old one built in 1970s.

Need a certified technician to install an RJ11/NBN wall socket for internet access. The apartment only has an old 600-series telephone terminal. There is no modern RJ11 or NBN-ready socket installed.

We need 2 ceiling fans installed. 1 x in small home office 1 x front lounge room. New ceiling fans provided. Must be a qualified electrician. Install ASAP. Thanks.

Disconnect old oven and connect a new oven. Need LICENCED ELECTRICIAN. Located in Eastwood NSW 2122. I am pretty flexible with the timing. No need disposal. Thanks

Needing an electrician to fix or replace bedroom lights they are hardwired bulbs still work however they work intermittently and flicker and then shut off it could be the driver unsure needing someone experienced

Hello, We are looking for a licensed NSW Electrician to diagnose and repair a faulty illuminated sign at our retail store, in Macquarie Centre. The Issue: Our vertical, illuminated "EYETESTS" sign, which is mounted on a pivoting door, has an electrical fault. The light only turns on when the door is open and goes out when the door is closed. This strongly indicates a broken, loose, or frayed wire in the cable that runs from the wall into the moving door, likely at the hinge or pivot point. The Job: The task is to find and repair the wiring fault to ensure the sign remains consistently lit, regardless of the door's position. The scope of work includes: 1. Safely isolating power to the circuit. 2. Diagnosing the exact location of the break or loose connection in the wiring. 3. Performing a durable repair. This may involve splicing the wire, re-terminating connections, or replacing a small section of the cable to ensure it can withstand the repeated motion of the door. 4. Testing the sign thoroughly by opening and closing the door multiple times to confirm the light stays on reliably. Requirements: - MUST be a fully licensed and insured NSW Electrician. This is essential for safety and compliance. - You must have your own diagnostic tools (e.g., multimeter) and electrical repair equipment. - Experience with fault-finding in commercial settings or on moving fixtures is highly desirable. Location & Timing: Location: Macquarie Centre, Cnr Herring Rd &, Waterloo Rd, North Ryde NSW 2113 (exact location will be provided once the task is assigned). When: The job can be completed at your earliest convenience. Please state your availability in your offer. Please provide a comprehensive quote for the complete job. Your offer should include your call-out fee and all labour required to diagnose and repair the fault. Thank you.

Hi,I have four downlights in my bedroom, and one of them has stopped working. I tested the light by swapping it to another position, and it works fine, so the bulb itself isn’t the issue. I also replaced the transformer, but that didn’t fix the problem, so it’s likely something else causing it. The other three lights are working perfectly. Please provide me with a quote that includes diagnosing the issue and fixing the light, including both labour and material costs.

Need to add socket for washer and dryer. Looks like power in the Greg box on the bottom left of picture. Would need to look at that connecting to it and putting a socket beside it. Socket can be external

1) Need to install lights in the bathroom. 2) Fan is not working. Need to check