Find trusted local electricians in VIC

Power switch keeps cutting out from machine and dryer - currently using 1 switch with a powerboard (might need a double switch) Also looking at installing outdoor lights - currently don’t have an outdoor power unit

Loose power point in the bathroom

Replace two bathroom extractor fans and connect the ductwork vents out through the eaves/soffit. We have all the parts. No changes to the current switches or plugs. Only to replace the extractor fans and install new duct and vent. Bathrooms are on the first floor. Current fans have round hole so the new ones should fit or may need to cut the ceiling a bit to fit. House is two levels, manhole is accessible. Tiled roof, standard pitch.

I’m looking for a licensed electrician to upgrade an older ceramic fuse switchboard at a residential property in Maidstone. House is single phase and has existing solar system connected. Scope of works: • Assessment of existing ceramic fuse board • Upgrade to modern single-phase switchboard with circuit breakers • Installation of RCD safety switches (as required to meet current standards) • Compliance certificate (of electrical safety) on completion

Need PowerPoint install completed x2 Brick wall or underground available for convenience (600 deep already dug)

The upstairs hallway and a few downstairs downlights keep flashing. We replaced them with new lights, but the problem is still there. Both upstairs and downstairs are on the same circuit. I think one of the cables might be damaged.

Bedrooms x 2 need an additional power point, only have one in each room and all are poorly positioned. Would also like to hide wires from TV in loungeroom with new point if possible.

Gas leak smell near hot water heater. Gas has been turned off and needs to be restored.

need smoke alarm provided and installed

I need to replace a couple of outdoor light fittings. Current wiring seems to not have the earth wire and this may need to be added Looking for a licensed electrician that can work on this. See photos attached

I need a licensed electrician to replace an outdoor 240V pedestal/bollard light in Mount Eliza today. The existing stainless steel pedestal light is to be removed & a new pedestal light fitting to be installed (like-for-like replacement). The wiring is already in place at the base. Scope of works: • Disconnect & remove old pedestal fitting • Install & secure new pedestal light • Connect to existing 240V wiring • Ensure weatherproof sealing • Test & confirm working correctly • Leave area tidy This is located in the garden beside a path (easy access). Must be: • Fully licensed electrician • Able to complete the job today Location: Mount Eliza

I have very tall ceilings and don't have a ladder tall enough, so I need someone to change the battery on one smoke alarm and the globe on a light fitting. I have the batteries and globes required.

Hi. My frost valve is leaking on my solar water panels and I need it replaced. Tempted to do it myself but get nervous at thought of being on the roof. I have ladder here you can use. I don’t have the part.

60cm wall over needs to be disconnected. Also need quote when on site to install power point for new plug and play oven. See picture for wired-in oven connection.

1. Fix hallway lights (tried new globe still no good) 3. Move PowerPoint besides stove to bottom of wall 4. Move ceiling fan from kitchen area to spare room

Looking for someone who can come pretty much now and fix a wire on a Honda cbr that has been partially melted with what appears to be a jet lighter. It's not melted all the way through but enough to be messing with the electronics. Should be a pretty straightforward job for someone who knows what they're doing, only one fairing to be removed. Needs to be done asap.

We are after 20 downlights to be installed This is to be spread over 3 rooms & hallway (living room, dining room, kitchen & hallway) We have a light switch on/off circuit breaker on our fuse box We would also ideally want the existing lights decommissioned and/or removed (Though this is not critical, kindly include a price as an optional extra and see photos attached) When you give an offer, mention if it is with downlights supplied as we are happy to supply if necessary (and also provide exactly which downlights will be supplied make/model no.) We are after white variation colours (where type of brightness is adjustable) and dimmable ideally (though potentially only one room will be dimmable being the living room) We are after a licensed electrician (Provide your license number in Victoria to be considered), have active ABN and insured aswell We are flexible on the time of installation over the next couple of weeks. Let us know exactly when you plan on completing the job in the offer

Hi there, One of the buttons on my 4 button light switch is broken and I need it replaced. I have the part but just need it swapped out. I hope you can help.

Install 7 LED downlights (replace existing E27 recessed fittings, 150mm holes) I need a licensed electrician to replace 7 existing E27 recessed light fittings with integrated LED downlights. Details: • Quantity: 7 lights • Current fittings: E27 recessed bulb fittings • Hole size: approx. 150mm diameter • Location: Residential property, standard ceiling height • Scope: Remove existing fittings and install new LED downlights • Must be licensed and provide compliant installation Please advise: • Whether I should supply the downlights or if you can supply them • Recommended downlight size/type to suit 150mm cut-outs • Total cost including labour and materials (if supplied) Lights can be supplied by me if you confirm suitable model.

Need heavy duty Plug Point for outside Alfresco For fridge. Can take connection from Washing Machine Nearby.