Find trusted local electricians in Ryde

Provide Rheem 160-170 liter gas hot water heater or comparable. Remove old unit Install North Ryde

change celing down light at Charles street canterbury

1) replace 2 x power points inside (supplied) 2) replace two power switches inside ( supplied) 3) replace 7 outdoor lights (lights supplied SAL Brand) 4) replace 2 x garage light battens (supplied) The painting and eaves fix should be done this week weather permitting so after this is done need the lights replaced.

Hi, I have purchased a new toilet seat which connects to water and electricity, it does wash and it heats up for my parents in Sydney. It could be a easy way to fit im not really sure. I'm not there and I don't want my dad try to fix it. I have the picture here and they have water tap next to their toilet so no plumbing required.

install WiFi relay control on two pool/spa heat pumps (8.7A and 17.5A, 240V). Parts on hand: Shelly Pro 2PM, 25A AC-3 contactor, RC snubber. Mount on existing DIN rail in switchboard, wire smaller unit direct through one relay channel with snubber fitted, larger unit through the contactor via the second channel. Existing isolators stay in place.

I need 3 phase disconnected / switched off from commercial building while I paint around external cable fixing point . It will need to be off for 60 minutes or less.

2 power points are shorting out

* Install 2 × 1200mm LED blade lights * Connect to the existing electrical wiring and switches. * Securely mount and align both lights. Note: I have already purchased the 2 new LED blade lights. Only installation is required.

Looking for a licensed electrician to install a new pendant light. * Existing light has already been removed. * Mounting bracket and holes are already in place (see photos). * The new pendant light is assembled and ready to install. * Just needs to be wired, mounted securely, and tested to ensure it’s working properly. Please bring any standard tools you may need. Located in Epping, NSW. Looking to have it done as soon as possible. Please send through your quote and availability. Thank you!

I need a licenced electrician to install a single phase EV charger. I require a 16m cable to be run from the electrician board to roof and down the side of the garage to the outside wall. Single storey house. Job to include cable and parts, wall charger supplied by me

Handyman/Electrician need for a few jobs around the home: Few minor electrical jobs - Replace wall socket in kitchen (pictured) - will need to supply wall socket - Replace GU10 bulbs in 3-in-1 Martec unit - I will supply the bulbs Assemble sideboard purchased from Temple & Webster: https://www.templeandwebster.com.au/Brianna-4-Door-Sideboard-TMPL5453.html

We are having some modifications done in our Kitchen to install a small cutlery drawer above our microwave oven (as a separate Airtasker Task). However, for that task to go ahead, we need to ensure the Power Point to our Microwave Oven does not clash with the new drawer to be installed. The current Power Point is in the top left hand corner of the enclosure, we require it to be moved downwards by about 100 to 150mm. I think the Power Outlet is surface mounted to the back of the enclosure, and from what I can tell, the power cable comes into it from the cabinet wall on the left hand side, which is the sink enclosure.

Electrician to install double power outlet, 4 lighting fixtures, and 2 dimmer switches. Existing wiring all already there.

Please can you provide a quotation for the electrical testing and tagging of 600 assets?

Details: I need a licensed electrician to replace an old 2-gang wall light switch (see photo) with a new one. Existing switch works but is worn and slightly misaligned. Looking for a clean, safe install and proper alignment. Scope: Remove existing switch Supply & install new 2-gang switch (or install one I provide) Ensure wiring is safe/compliant Test both switches

Looking for a licensed electrician to replace 2 existing LED downlights in a bedroom. This is a straightforward swap of existing fittings - easy access (no high ceilings). The current setup uses a standard LED downlight with external driver. What is required: - Supply and install 2 new LED warm downlights - Disconnect old units and connect new ones Downlight specifications (based on existing unit): - Approx. 90–92mm cut-out - 10W LED (or equivalent) - IP44 rating preferred - Standard white trim Please include supply of suitable downlights in your quote.

Hi, I need help with electrical stuff in my apt the last 3 months One of the safety switch( for wall sockets around the house) keep turn off everytime I turn or random powerboards around the house, connected to TV, laptop, or hair dryer. After a while, Its back to normal, or have to turn off something to get everything else work again.

Electrician needed — safety check on kitchen ceiling light fitting after water contact I need a licensed electrician to attend a residential apartment and carry out a safety inspection of a ceiling light fitting that was exposed to water during a leak approximately one week ago. The fitting is not visibly damaged but water was observed dripping over the fitting at the time of the leak. The tenant has not used the light since and I want formal confirmation it is safe before they do. What I need: • Inspect the ceiling light fitting and associated wiring for any moisture ingress, insulation damage or corrosion • Test insulation resistance if appropriate The job should be straightforward if no damage is found — I'm not expecting a full electrical inspection, just a targeted safety check on this one fitting.

Electrical switch went in and need to take it out and fix it. Please see photo.

Hi, I have a double power point in my kitchen that is broken. Looking for a licensed electrician to replace it with a new double GPO. I am located in Epping (near Rawson St). Preferably looking for Alan T. if available! Thanks.