Find local electrical rewiring electricians in NSW

replace 2 light switches so they work and fir 1 light to kitchen ceiling, light switches and light fitting already here.

Need to just cut and rewire fridge and kitchen outlet

Supply and install 20amp rcbo Run new dedicated power circuit Supply and install double PowerPoint on mounting block Add additional double PowerPoint on mounting block Run 2x cat6 cables from server room to office - install 2x mounting block one in either room - install 2x data jacks on each mouthing block 4x in total

Licensed Electrician needed to rewire heater circuit to main with DIN smart switch + manual contractor Looking for a qualified licensed electrician to complete a quick switchboard modification so I can dynamically control my heater based on home solar generation: - Circuit Move: Swap an existing heater load wire of the controlled-load / off-peak meter loop and onto a general supply circuit breaker. - Module Installation: Install and wire 2x DIN modules: 1x Shelly Pro EM-50 (i am supplying this one already purchased see picture) 1x 25A Manual Override Contractor. Happy to supply this one as well if you tell me which one to get unless you can supply it, add it to quote. Cable to the switchboard is already in place. I will handle all WIFI pairing, app setup and automation connection. Must issue a CCEW with the invoice upon completion, see attached picture happy to send more.

I have a 1970s standing lamp that needs to be rewired and a new switch added.

I have 2 lamps that I think need re-wiring. They flicker when switched on and I think it’s due to rust in the switch from the salt air.

Rewire plugs on extension cables - au, eu, uk etc. Ongoing basis, maybe 10 every fortnight roughly. I have all the materials and can drop off / pick up cables if you’re local in sydney. Price per cable (both plug and socket)

Currently have a Solar edge inverter system with 50 panels running optimises which are AC coupled into a SigEnergy battery. I would like someone to come and remove and rewire the optimises straight into the Sigenergy intevert and make it DC coupled essentially removing the need for the Soler Edge current inverters. 50 panels currently on optimises

I have two vintage lamps, purchased overseas. Both need to be rewired for Australian standards.

Repair a table lamp by replacing socket and wire to unit. Desk lamp needs to be wired for Australia.

I’m looking for a qualified electrician or experienced neon/LED signage technician to repair my neon sign. The sign appears to have an electrical fault/short circuit, and part of the circuit may be burnt or damaged. I believe it may need to be rewired and/or have damaged electrical components replaced. I’m looking for someone who can: Diagnose the electrical fault Identify any burnt/damaged wiring or circuit components Repair or rewire the partof thte circuit that is damaged, then Test the sign and ensure it is working safely Budget: $120, negotiable depending on the repair required. Please only apply if you have experience working with neon/LED signs, illuminated signage or electrical wiring.

Rewire floor lamp. Works but temperamental. Can drop to you within 10kms of Marrickville (2204)

Floor lamp needs to be rewired. Currently works but temperamental.

I have a Rheem Stellar 315L(model 4A1315M8) currently on an AGL Controlled Load Circuit. I need a LEVEL 2 ASP to completely disconnect it from the off-peak meter/network ripple relay, submit the network abolition paperwork to AGL, and rewire the tank into my main general house consumer mains circuit. Please instal a DIN-Rail Digital Timer and Switchboard Contactor set to run the tank only between 10.00 AM and 3:00 PM so it can run off my Solis/Fox ESS Solar setup.

I need the electricals replaced in two table lamps

Rewire small cottage and garage, change power points and light battens and upgrade switchboard. Will provide all materials - just need labour for 5 days.

U can drop it off and collect. It’s a standing lamp that has stopped working recently. Not new, but also not that old,

Rewire a light switch. External, wall mounted cabling running 1.5m to new light fitting. Light fitting provided.

Need the plug to a radiant heater replacing . You don't need to be an electrician but you do need to be confident you can do this safely.

We bought some lights off Etsy and whilst all the electrical is in order, they are not Australian certified. They are travertine reading lights, with LEDs. Looking for an electrician or lighting repair specialist to assess whether these imported Etsy LED reading lights can be safely rewired with Australian-approved components and installed. If possible, we’d also like them electrically tested. Plus, we have a tall lounge room lamp, but the foot switch has stopped working and doesn’t stay on, it only stays on if you keep your foot on it