Find trusted local electricians in Inner South West Sydney

Change 3 outdoor lights I have the new ones ready .

Looking for a licensed electrician to inspect my existing built-in oven setup before I purchase a replacement. I currently have a SMEG SA420X 60cm built-in electric oven (approx. 3.0kW) installed underneath a separate SMEG gas cooktop. The oven is no longer working due to the control panels buttons melted and I would like to replace it (unless fixing is a better option) Before purchasing a new oven, I would like someone to: • Measure and confirm the existing oven cavity dimensions • Check the existing electrical connection, circuit and available capacity • Confirm what specifications I need for a straightforward like-for-like replacement with no modifications • Confirm whether a Westinghouse WVE615SCA (3.0kW hardwired) would be a straightforward replacement • Advise whether my existing electrical setup can accommodate a higher-spec/higher-powered oven (e.g. 3.5–3.6kW) without upgrading the circuit • If an electrical upgrade would be required, advise what work would be involved and approximately how much it would cost, so I can decide whether upgrading the oven is worthwhile I would ideally like to use the same electrician to return and remove the existing oven and install the new one once I have purchased it. Please also provide an installation quote following the inspection. Licensed electrician only please. 📍 Wolli Creek NSW 2205

Disconnect and removal of internal pendant lights x3, removal of power points, removal of external flood light, and disconnection of outdoor illuminated signage.

Remove 3 old rusty fluorescent light fittings and install 3 new weatherproof fluorescent style LED in the same location under metal carport. New fittings are supplied by me.

We have three outdoor lights in sequence which are not getting power following replacement of lights with new lights. Need an electrician to check and fix.

4x Outdoor lights 3x Tapo outdoor cameras Single story brick house. We have one outdoor light we want to replace, the other 3 will need new electrical points. There’s cable running through the roof out to the eaves.

I need someone to remove an old hot water heater and install a new electric hot water heater

Scope of Work: 1. Removal & Installation * Remove 4 existing light fixtures (3 bedrooms, 1 living room). * Assemble and install 4 x supplied DC ceiling fans with integrated LED lights and remotes. * Single-storey house with ~2.7m ceiling height. 2. Testing * Ensure proper joist mounting and balance. * Program remotes and test speed/light functions. Requirements: * Must be a licensed electrician (please provide licence number in offer). Materials & Site Info: * LABOUR ONLY. All 4 ceiling fans, light kits, and remotes will be supplied on-site. * Easy ladder access; wiring already in place at existing light points.

IKEA Kitchen install filler panel above PLUS Electrician to replace built-in mirowave

Hi I need a electrician to take down the ikea lights and install new chandelier lights today. Chandelier requires some assembly to make the picture. I can probs assemble it myself (edit: just finished assembling the chandelier parts) but I would love some person who can install it better and aligned to the ceiling than the airtasker who installed the previous one and also have some white spray paint if they have any to spray the wall. Can add $25 for the spray paint

For a licensed professional electrician to install four downlights in the new ceiling of our kitchen and also install an electric oven and install a double PowerPoint from the current rough in work down by another electrician

Need an electrician to replace existing sensor light with wired arlo spot light

The RCD labelled “Protected Power” (C20, 30mA) trips the instant I switch it on, so all power points are dead. Lighting circuit is fine. Cause is known: insecticide spray went into one power point and the tripping started immediately after. The RCD has been off since and I haven’t touched the outlet. What I need: the affected outlet inspected and replaced, and the circuit tested.

I currently have a Martec Contour 2 connected to a 3 gang switch and the fan exhaust is not working so needs to be replaced. The main bathroom lights and lights on Martec unit are on the same switch. I plan on buying Martec Profile 2 and need an electrician to help replace and connect to 3 gang switch. This may require existing cutout to be extended to fit new system. Any recommendations on any other bathroom heater and fan exhausts are welcomed.

I have an external power point that I need installed by a licenced electrician. I will supply the materials (external weatherproof power point)

I need to replace 2 power points and 2 light switches. 1 set is in the bathroom on a tile and the other is in bedroom. I have the replacement parts. Just need to replace them and fit them on the wall/tiles

I am looking for a fully licensed NSW electrician to supply and install one new extra power point in a bathroom at a single story house in Padstow and able to provide CCEW. Just take extra care of the wall tiles.

I'm looking for a licensed and insured electrician/gas fitter to complete the following work at my property in Arncliffe, NSW, as soon as possible. Scope of work: Rangehood Replacement Remove existing rangehood. Supply not required (I already have the new unit). Install a new Solt 60cm Slide-Out Rangehood (Stainless Steel). Gas Cooktop Replacement Remove existing gas cooktop. Install and connect a new Chef 60cm Gas Cooktop (Stainless Steel). Ensure the appliance is tested and operating safely after installation. Requirements: Must hold the appropriate licence(s) to carry out the work. Please bring any standard installation materials if required Please provide a competitive quote before commencing the job. An invoice is required upon completion. The job is located in Arncliffe Please contact me with your availability, licence details, and quote. Thank you!

Need a licensed electrician to replace 3 light switches, 3 double power points and 1 bathroom batten light fitting. I have already purchased all the replacement fittings. Please install them and test that everything is working properly. Photos attached

Need some cables running in kitchen for new power sockets On the image, the Red is existing power The left hand corner is where the mains power for the cooker is which will need running behind to where the new cooker placement is going. I’ll need power new slot which is the green section and there is another PowerPoint below at the bottom of the kitchen the back which will be used for the cooktop but currently doesn’t seem to be given off any power.