Find trusted local electricians in Donvale

I need (1) smoke alarm check and compliance certificate issued as per VIC govt legislation for annual smoke alarm rental property check and (2) replace 2 x damaged powerpoints at the same property (see photos of the 2 damaged powerpoints) Please make your offer inclusive of all materials, labour, compliance certificate and airtasker fees

I have approx 21 down light need to be changed to down light Dismantle the current light setting and change to down light Dismantle the Security intercom system

Need 3x outdoor wall lights replaced. First photo is existing light to be removed, second photo is of the new lights for installation. All 3 are the same.

Looking to have household electrical items sorted as per mark up attached. Job to include compliance certificate.

Lights are outdue to short circuit in ceiling light lamp wire..

Install a 5-pin socket, wiring to electrical box and upgrade RCD to support an electric vehicle charger on a dedicated 40A circuit breaker. Install 8x 90mm LED downlights and wiring in the ceiling of a single story home in the dining room area.

I need a new electrical cable drawn from the switchboard to my bedroom (~8m) with a new separate circuit breaker switch installed. For cabling it can be easily accessed from the ceiling through a manhole.

I am having a two point electrical outlet removed. This will leave a hole in the wall that I want patched and painted over to look natural against the rest of the wall. I have the paint and will supply it.

Electrical Safety check for Certificate of Compliance.

Dead easy job for person with right skill set. I need someone to change an external 'safety light' fitting. The fitting is a Crompton Australian sourced acrylic ball type light fitting mounted on a rigid upright pole. (see photos) The fitting received a very light knock from a vehicle which fractured the collar fitting on the fitting itself. There was/is no damage to the wiring and the globe actually still works. Only the dome (connector lugs) were damaged. I have the identical original (spare) unit on hand as pictured, so I know it is a one for one exchange. Basically just remove the collar and replace the wiring into the new base. The previous installer did use a light amount of silicone sealant around the base collar, otherwise it would be very much a handyman job other than working with 240 volts. This should be a dead easy job for anyone who has the appropriate skills. Pole is only 5 foot high, so no aerial work. Area around pole is 100% clear as shown in picture and easy to work in. I understand fully that my asking quote may have to be slightly reviewed on site, if the job proves to have any complications. I am a 100% reasonable AirTasker home owner. There should not be any such problems of course. (as I see it)

The switch is pushed in and the power point can't be used

Part of our house power plugs are not working. Some of the switches form meter keep on tripping. Tried turning off few appliances but still not working.

Existing, damaged ceiling light fitting to be replaced with new Temple & Webster flush mount ceiling light

I need a pendant installed in kitchen by an electrician

Sensor not working and light just flashes intermittently. whole unit will need to be replaced with the new one pictured

Need 2 globes changed, one was replaced but won’t work. Also need two switches replaced, have bought the replacements.

Need a new stove and rangehood installed. I can get the old one taken out and removed before you arrive to do the job.

I bought this lamp off Amazon US without thinking about the wiring. I need someone to help me make it work here - this may be as simple as changing the US plug to AU (note that I have tried to use an adaptor and it doesn’t work, so maybe there’s more to it - please tell me if so). The lamp is hollow and the wire tracks up the middle of it, so removing it shouldn’t be too difficult https://www.amazon.com/gp/aw/d/B001BZHNSA?psc=1&ref=ppx_pop_mob_b_asin_title

We moved the spa a few meters and now the power socket is too far and it needs to be moved. A grade electricians only please

I need a light bulb holder installed in the ceiling, the electrical wiring already exists. There is easy access to the ceiling area.