Find experienced local carpenters in VIC

Face of joinery drawer has fallen off and needs repair.

1. modify joinery (1st photo) to remove shelves vertical and horizontal above draw patch wall 2. Remove desk joinery and above cupboard - patch /tidy up wall. 3. Remove robe joinery Remove rubbish Paint be others

1. modify joinery (1st photo) to remove shelves vertical and horizontal above draw patch wall 2. Remove desk joinery and above cupboard - patch /tidy up wall. 3. Remove robe joinery Remove rubbish Paint be others

joinery for wardrobes. offer solution and ideas before ordering doors and panels. Then to intall. 3 x bedrooms with 2 wardrobes in each room. Photo below shows layout of all 3 rooms. Close up on the complete skirting boards/ gaps between wall and fireplace. (wardrobes are yet to be secure)

I have 3 joinery units that need assembled. They need to be assembled like professional wardrobes. Need to cut skirting in some places and install fillers. Clear Caulking at the edges. One cut out for switch board required. Joinery is all in flatpacks. Need professional installers.

The front joinery panel has detached from my dishwasher on one side, and the joinery panel under the dishwasher requires securing. Would love some help.

Prepare a 600mm dishwasher cavity in a new kitchen by trimming floor scotia flush with cabinet sides and drilling a service hole through the cabinet. Feed hoses through, connect to existing sink plumbing, and slide dishwasher into position. Care required to avoid damage to new flooring and cabinetry. Tools required. Dimensions = 60cm width, 60cm depth, 85cm height

Price discussed upon inspection. I’m looking for an experienced cabinet maker or handyman to install laundry joinery in my garage. I have a general layout in mind (see attached image for reference), and would like someone who can help install cabinetry and make adjustments to best utilise the space. Scope of work: • Install laundry cabinets/joinery • Ensure a clean, aligned finish • Make adjustments on-site to suit the space • General fitting and finishing work Looking for someone who: • Has experience with cabinetry or similar installations • Can ensure a neat, professional finish • Can problem-solve on-site if needed Please include your experience and any examples of similar work. Happy to discuss further details or arrange a site visit.

Hello. We have recently had floorboards installed in our house. We need someone to cut the carpet and connect to where the floorboards finish underneath x2 doors. Attached two photos. One is our current situation and the second is what we would like.

Peeling melamine edge repair. We require a joinery repair for a kitchen pantry filler panel. The job will involve two visits - first to remove the panel for assessment, then a return visit for repair or replacement. Job scheduled for Monday, 13/04/2026 between 3:00pm - 5:00pm.

Job Summary: Kitchen joinery repair required at a residential property in Bentleigh East (VIC 3165). Scope of work: Remove one pantry filler panel (edging cracked) in kitchen Panel to be taken off carefully for replacement/assessment PS: Budget is indicative only. Please provide your quote based on the scope.

Hi, I’m looking for an experienced joiner or cabinet maker to assemble and finish a set of floating shelves for a salon in Elsternwick. All components are pre-cut and machined, I just need someone skilled to assemble, glue, and finish them properly to a high standard. ⸻ Shelf specs: • 3x shelves: 900 x 250 x 44mm • 2x shelves: 900 x 200 x 44mm ⸻ Each shelf includes: • 16mm laminate (Cinnamon Walnut – ForestOne) • 12mm chipboard core (with pre-made 25mm spacing for threaded rods) • 16mm laminate (Cinnamon Walnut – ForestOne) ⸻ Work required: • Assemble layers using contact adhesive • Ensure perfect alignment and clean finish • Apply laminate edging • Light sanding/finishing if needed • High attention to detail (these will be visible in a client-facing salon) ⸻ Important: • You must have your own workshop / space to complete the job • Shelves will need to be assembled off-site • Final pieces must be delivered to: 27 Horne St, Elsternwick ⸻ Timing: Must be completed and delivered before Saturday 11th April ⸻ Notes: • All boards are already cut and machined • Looking for someone reliable and experienced in cabinetry/joinery

Need joinery fridge door reinstating. I removed / unclipped the door when in the apt as our fridge wouldn't fit with it on. Hardware / hinges etc should still be on the door and just needs clipping on (not 100% sure). I have moved out of the apt and needs to be done in order to start bond process.

I need a professional installer to assemble prefabricated banquette seating base on site, you would need to glue brass laminate on kicker face on site. Curved banquette slit into 8 sections. Kicker and seat base a separate frames. I can provide all tools, if needed, including spray guns and contact adhesive, screws, etc. Please note, the offer is rate per hour. Scope of work, hours are subject to agreement.

Looking for an experienced cabinet installer for a residential project. Scope includes installation of pre-made cabinets, alignment, leveling, and secure fixing. Attention to detail is very important – clean and precise finish required. Must have prior experience in cabinet/joinery installation, own tools, and be reliable. Location: Hawthorn Timing: weekend Please send your quote (hourly or per job), availability, and photos of previous work. I am comparing multiple quotes, so please provide your best price upfront. Potential for ongoing work for the right person. Only experienced installers please – not suitable for beginners.

I have 2 sections of gutter that have come loose from the fascia (clips/brackets have come off) and one corner joiner has broken, so the gutter is slightly hanging. Looking for someone to: • Reattach/replace gutter clips • Replace or reseal the corner joiner • Ensure gutter is secure and aligned properly Single storey house, easy access. Job is straightforward – should be quick for someone experienced.

Door knob, change shower hose & 2 Blind Chain Joiners Need to change a Door knob, shower hose, 2 Blind Chains Joiners, 2 Fly Screens handyman & Vacuum clean ducted heating and cooling, two vents. Please quote for the labour only; parts costs will be reimbursed against your bunnings receipt separately.

Ikea or Kabooble laundry room joinery. We need to: 1) Install a broom cabinet, double door wall mounted cabinet, floor cabinets. 2) replace laundry trouph/sink, which we will supply. The width of the space is 180cm. The cabinets will need to be positioned against the wall shown in the pictures.

Supply and install additional black joinery shelf to existing cabinet, including all fixings. Refer attached photos for what the cabinet looks like, and tape measure against the dimensions. Shelf needs to be approximately 470mm deep x 705mm wide x 16mm thick (to match existing). I will remove all of the glassware and storage items and re-put them back myself once new shelf is installed. Let me know if you need any additional info.

I need this middle floating shelf removed so I can use a standing desk. Cut away shelf, remove/shave back rods/dowels, sand back and paint VJ boards and walls where attached (or I can do paining if left neat)