Find experienced local carpenters in North Strathfield

I have a small area that is a pit with a low brick wall around it. At the moment it has corrugated iron sitting on top. I mangaged to get some decking planks the correct size and quantity to make a small deck. I need someone to build the frame that the decking with sit on and secure the planks to the frame. I have a photo of the planks sitting on the tin to indicate what it will look like. Will need experience and tools and able to complete the job.

repost: need to put a partition wall and a door for space 2250 high x 1150 wide x 140 wall thickness. want to match the door and knob to the unit, https://www.bunnings.com.au/hume-doors-timber-820-x-2040-x-35mm-internal-door-primed-mdf-moulded-panel-caprice_p1970852 https://www.bunnings.com.au/gainsborough-satin-chrome-g4-series-left-handed-olive-dummy-leverset_p4020227 few things to note, skirting board, tile under timber flooring, side wall is concrete or brick not sure, top is A/C box with thin timber so probably hard to nail in the timber frame apartment unit - Due date: Before Saturday, 16 December 2023 - Due date: Flexible

need to put a partition wall and a door for space 2250 high x 1150 wide x 140 wall thickness. want to match the door and knob to the unit, https://www.bunnings.com.au/hume-doors-timber-820-x-2040-x-35mm-internal-door-primed-mdf-moulded-panel-caprice_p1970852 https://www.bunnings.com.au/gainsborough-satin-chrome-g4-series-left-handed-olive-dummy-leverset_p4020227 few things to note, skirting board, tile under timber flooring, side wall is concrete or brick not sure, top is A/C box with thin timber so probably hard to nail in the timber frame apartment unit - Due date: Before Saturday, 16 December 2023

Looking for someone to source, purchase and install a benchtop for an office kitchenette. Old benchtop must be taken down and new one installed as part of our make good for the end of lease. Dimensions are: 1950mm x 600mm x 38mm - Due date: Before Tuesday, 5 September 2023

Installation of timber slatted wall panels ~2.7m in total length. Also 3 floating shelves need to be put up. - Due date: Flexible

Had a roof leak and has left small stains on 2 places on the ceiling (see photos). Looking for someone to colour match and paint over stains. Would like the paint to match the ceiling as close as possible and blend. - Due date: Before Saturday, 25 February 2023

Assemble a Keter plastic garden shed with plastic floor on lawn, size :7x7 (2.1W x 2.1D x 2.2H) - Due date: ASAP

Looking for an experienced carpenter to modify an existing van build. I believe it's a simple task for someone experienced but willing to negotiate if it turns out to be complex. - Need cabinets shortened to widen the bed - under bed storage created with lift up lid to access - wall behind cabinet finished with tongue and groove wood panels - recycle and reuse materials as much as possible - will pay for additional materials but you do the shopping - van can be transported to your workshop Great if you can complete by 9th Feb otherwise flexible due date - Due date: Flexible

Build a deck frame on an existing concrete slab (3m x 3 m slab). The deck frame will be used as a base for a new garden shed - Due date: Flexible

Garden shed concrete base 8 sqm for PLASTIC garden shed. - Due date: Flexible

2.26x2.26m garden shed concrete base - Due date: Flexible

Need window frames , doors, fence and garage front refinished and painted in natural cedar colour preferably using a marine varnish semigloss - Due date: Flexible

Looking to make planter bed and a wooden bench in between Approximately 3m wide and maybe about 1m depth (not sure about the height yet but I'm assuming a 80cm height with the planter and 45cm height for the seating) With micro cement finish Located in North Strathfield, looking to do it in 2-3 weeks time - Due date: Flexible

Carpenter / handyman to plane window reveal back 1-2mm. Approx 10 lineal metres

Shoe cabinet bottom drawer has come undone, too drawer doesn’t open fully.

I'm looking to cut a step in some concrete. I made a start but the job is a bit beyond me. There is a little bit of reinforcement (metal) I have come across. The job is in a garage. There should be an image with dimensions. If not, the dimensions are approx. 30cm long, approx. 50cm wide and 22cm deep.

I would like to install a dog door ( for the size of a cocker spaniel) with housing into the large bottom window in the picture. Ideally the dog door will be housed into the bottom window to the height of the dog door and the top window will close on top of the housing securely. The size of the window insert is approx. 82w x 104h however as above, ideally the housing will just be the height of the actual dog door, not reaching the entire height of the window opening. Housing can be made up of timber or similar. I would like materials including the dog door to be included in the price

I require 1 x damaged floor board panel to be removed and replaced with a new panel. There is also a cover between the door and the outside carpet that needs to be replaced. I will purchase the floorboard and the cover so it will be just the labour required. I can also send pictures to give more context.

I have some small damages in my inbuilt wardrobe caused by some burns. I was wondering if someone could help me repair it, I am unsure of the cost so please let me know

Need quad moulding cut and installed to cover an ugly gap between the skirting and the floorboards in a rental I've moved into. I would pay for the moulding itself and nails/liquid nails and then pay by the hour for your time, 50/hr. BYO tools. There are three rooms in total, dimensions (mm) are: 449 x 420 435 x 295 580 x 367 I need a quote for total estimated hours