Find experienced local carpenters in NSW

Hang 2 small stainless steel shelves, and unscrew picture screws in living room

Current shelving is fixed to wall with stainless sheeting. Remove and move and fix to tiled wall, wall is made of concrete block behind tiles. Care to not damage tiles. Silicone around fixing to avoid water damage behind tiles ?

Looking for a professional cabinet maker to make and install small corner storage cupboard and cupboards above window and door in laundry room.

looking to get a quote for: •Install bathroom shaving Cabinet 1600 x 1100 x 40 - supplied (see photo of wall) •move existing down light to centre of cabinet (see photo) •relocate power point to inside cabinet (see photo of existing power point)

Looking for an experienced cabinetmaker/joiner/carpenter to measure, supply, manufacture and install custom shelving to match existing dark walnut kitchen cabinetry. Area 1: Floating shelves in the narrow space between the right-hand cabinetry and wall/window. Ideally concealed fixings with no visible brackets. Area 2: One custom shelf spanning the open space underneath the centre overhead cabinets. Existing cabinetry has a dark walnut/oak-look finish. Looking for the closest practical colour and grain match. Happy with timber veneer, stained timber or matching laminate depending on what gives the best result. Price to include measuring, materials, cutting, finishing/staining, fixings and installation.

Reception desk: approx. 1.588m Hallway cabinetry: 1.5m Kitchen/staff cabinetry: 1.85m Laundry/storage cabinetry: 3.97m Total visible length: approx. 8.9m — allow around 10m including curved section, returns and waste. Plinth height: approx. 100mm Preferred aluminium thickness: 1.6mm Reception includes a curved end that needs to be wrapped neatly.

Help me put up some mirrors on new tiled bathroom wall and inside joinery. See mirror details below. Purely just a glue to wall job but want support to ensure its done correctly 6mm Silver Polished edges 1-1404 x 1300 4mm Silver Polished edges 1-450 x 1650 1-450 x 1000 2-370 x1100 Thanks Henry

Hi, I need a carpenter/handyman for a small garage fitout in Smithfield 2164. Job: • Install slat wall panels / tool boards on garage walls • Securely fix to brick/plaster wall, level and straight • Add timber batten frame if needed • I also have some shelving to install after Please bring: drill, level, stud finder, fixings suitable for masonry. Location: Smithfield NSW 2164 Parking available. Can do weekdays or weekend. Please quote labour only and labour + materials. No fixed budget - open to offers.

I need a small section cut out of a kitchen cabinet shelf to fit my new refrigerator into place, in Pyrmont . The cabinet is above the fridge and only half depth, so only the front portion of the shelf needs a notch cut. The cutout needs to be roughly six inches by six inches to clear a raised cap on top of the fridge. This should be a short job for someone experienced with carpentry or cabinetry who has their own tools. Ideally completed this coming weekend. Budget around 80 to 150 dollars, happy to discuss based on your quote.

Looking for a painter to prime with a stain blocking base and repaint a room. Dimensions approx 2.84m by 3.59m, plus the ceiling. One wall has a window which is approx 1.795m wide by 1.47m high. Bring your own tools and products and include all labour and materials in the quote. Prefer not to remove the wall mounted AC. Wall mounted TV either needs safe removal and remount, or paint carefully around it.

The wooden wall on our deck is in the verge on falling apart. Need carpentry skills to fix that.

Need an experienced joiner to go to site and level kick bases, put base cabinets on screw together. Simple stuff easy money for someone who knows what they’re doing.

Drill and hang 8 custom IKEA kitchen cabinet doors — Crows Nest I need an experienced cabinetmaker, kitchen installer, or highly capable handyman to drill the concealed-hinge holes in 8 new custom cabinet doors, then fit and align them on my existing IKEA kitchen cabinetry. The cabinet carcasses and IKEA-style hinge mounting plates are already installed. The new doors are on site, still wrapped, and ready to be drilled and hung. Scope • Measure and mark each door based on the existing cabinet-side hinge/mounting-plate positions • Drill the correct hinge pattern for IKEA UTRUSTA / METOD-style concealed hinges • Fit hinges to each door and attach them to the existing mounting plates • Hang, align and adjust all 8 doors for consistent gaps and smooth opening/closing • Keep doors protected during work and clean up all drilling dust/debris Hinge details These are standard European-style concealed cup hinges: • 35 mm hinge-cup hole • Approx. 11.5–12 mm deep — absolutely must not drill through the front face • Two smaller adjacent locating/screw holes for the hinge hardware • Existing kitchen and hinge close-up are shown in the photos Important: Please confirm the exact cup-hole setback, vertical hinge positions and smaller-hole pattern from the actual existing hinges/cabinet locations before drilling. I do not want generic measurements used blindly. Ideally, test-fit one door first, confirm alignment, then complete the rest. Tools required Please bring appropriate tools, ideally including: • 35 mm Forstner bit or concealed-hinge drilling jig • Depth stop • Drill/driver and smaller drill bits • Measuring/marking tools, clamps, etc. Please confirm you have a suitable 35 mm hinge jig or Forstner bit with depth control. Budget and location Budget: $400 total for drilling, fitting, hanging and final adjustment of 8 doors. Located in Crows Nest, NSW. Flexible on day/time.

1. Replace/renovate cupboard to nicer one. 2. Add shelves (See pictures for example) 3. Add table top and sides design to enclose existing fridge area 4. Enclose top storage area with sliding doors to cover storage. Attached are photos of the place, plans and an AI example (preferably with wood colour that matches current wood in shop). Send your quotes. Happy to arrange an in person measure and quote as well.

I have 2 double door corner cabinets that dont close properly

We recently had blinds removed from around these timber doors/windows, and the top section has been left looking unfinished. I’m not exactly sure what needs to be done, but I’d like the top of the doors/windows to look the same as the timber sides, so it looks like there is one continuous, finished timber border all the way around. This may mean a new architrave to match the left and righthand sides Looking for someone experienced with carpentry/joinery who can look at the photos, advise on the best way to do this, and complete the work. Ideally the new timber/finish would match the existing frame as closely as possible. Please include your proposed approach and approximate materials cost in your offer. It would need to be done some time this Sunday or Monday. Thanks!

Kitchen & cabinetry dismantle – Bowral – 12/13 Sept We’re looking for an experienced kitchen installer, cabinetmaker or carpenter to carefully dismantle a kitchen and other cabinetry at a home in Bowral. Dates: 12–13 September, with 14 September available if required. Everything is being reused, so the cabinetry needs to be carefully dismantled, labelled and organised rather than demolished. The job includes: * Kitchen cabinetry and island * Stone/marble benchtops * Vanities * Built-in wardrobes * Banquette seating * Associated doors, panels, shelving and fittings Photos are attached and further measurements/details can be provided. Everything will need to be dismantled carefully, with components labelled and screws/fittings kept together, then organised and stacked in the garage ready for collection by our delivery driver. There are stone/marble benchtops, so please let us know if you’re comfortable removing these for reuse or if you recommend they are handled separately. Plumbing/electrical disconnections can be arranged separately where required. Potential follow-on work We are posting two separate installation jobs in Balmain for approximately 21/22 September: one for kitchen reinstallation and another for wardrobe/cabinetry reinstallation. If you’re interested in the follow-on work, please see our other Airtasker listings and let us know. We’d be happy to use the same person/team for dismantling and installation if it works. Please quote for the Bowral dismantling only on this task. When responding, please let us know your relevant experience, availability for 12–14 September, how many people you would bring and approximately how long you expect the job to take. Thanks!

Looking for someone experienced to oil/stain our new timber fence in Drummoyne. Fence is approximately 8.6m long × 2.1m high (18m²) * I will supply the timber oil * You supply brushes/rollers and all other equipment * Protect surrounding artificial grass, paving, walls and garden from drips/splashes * Leave the area clean and tidy afterwards Only the one visible side of the fence shown in the photo needs to be done. Looking for someone with experience.

See corner insert that rotted away because of leak from roof. Now leak is repaired. So need area cleaned up, then replaced with new timber (will be supplied). Can be glued or otherwise held together. (One part of the material may be asbestos material so best to be gentle). It's about 4 meters high, so need ladder

I’m looking for someone who can take down an old bathroom cabinet & build and put up a new one. The measurements of the old one are 60cm x 70cm & the new one is roughly 65cm x 70cm.