Find experienced local carpenters in Canberra

Just need to drill a hole into the desk - 60mm wide for a cable grommet

Some western red cedar boards are water damaged on eaves.

Needing ikea joinery assembly and installation in 2 x rooms. Removal of small kitchenette and assembly and installation of new one

I have a timber maple veneer french door with glass that needs to be stained. It will require prepping, pre-stain conditioner and then staining.

Deck had stairs that were rotted and broken. They have been removed. Need a carpenter to replace the old stairs. Posts will have to be dug for cement for the posts at the front. Pictures attached show where the stairs will go and also what the ones on the other side of the deck look like. If you want to come by and look before a final quote, that's fine. Many thanks.

We have a vinyl floor at work total floor area is 155sqm vinyl is wood shade with pattern in matt finish. I need it deep cleaned with a polish and stains removed

Installation of kitchen cabinet in garage

the measurement for the cupboards are .... width =140 cm height = 180 cm depth =35 cm we need 3 steps steps width = 90 cm steps total height =30 cm each step height = 10 cm steps depth =27 cm pullout tray width = 90 cm pull out tray thickness 2cm [under pullout tray need three drawers] drawer 1 =20 cm drawer 2 =25 cm drawer 3 = 30 cm lights = 3 Sample image attached. It can be simple

Install a new kitchen , all cabinets assembled no flat pack !

I have 3 cabinets which i would like to put doors on. All are 1100 high a d 680 wide Id like 2 in wood and 1 glass.

I have a job for carpenter and helper. Need to install shelves on commercial kitchen wall & bar shelves to be installed.

the wood transition strip of the flooring has come off and need someone to fix it.

I’m looking for a carpenter / builder to construct and install a recessed box inside a plasterboard wall behind a TV unit to hide power points, cables, and small devices. Approximate size: Width: ~100cm (may need to be reduced depending on stud placement) Height: ~30cm Depth: ~20–30cm There may be wall studs in the way, so the final width and framing approach will need to be determined on-site. I’m happy for the carpenter to adjust the design to suit the wall structure. Requirements: Cut plasterboard and frame a recessed cavity/media box Install a hinged lid/cover for access Ensure structure is secure and neatly finished Allow space for power points and cable management I will provide a diagram with measurements and layout for reference. Let me know if any materials should be supplied in advance or included in the quote. I will arrange electrician for the electrical.

We have a deck rail made of wood. We are about to get roller shutters installed and the deck rail needs to be shorter to fit the roller shutters. The company installing them said we would need to arrange this. You would need to use your own tools. The rail is approximately 35 mm thick. The piece to remove would be approximately 140 × 140 × 35 mm. There will be 2 pieces to cut off, one at each end of the rail. I have attached 3 photos, but there are only 2 bits to cut. We need to get this done before the roller shutters are installed. I don't have a date yet, but it will be in the next few weeks. Probably the sooner, the better.

Fix chipped wooden skirting boards.

I’d like to oil the deck and fix the patio doors (missing weather strips).

I am looking for someone to pressure wash a weathered timber fence in preparation for a stain application. The fence is one-year-old and weathered and needs a thorough clean to remove dirt, grime, mildew and built up residue so the stain can properly adhere. This task is for cleaning only. No staining or sealing is required. Scope of Work • Pressure wash timber fence panels and posts • Remove surface dirt, mould and weathering build up • Take care not to damage timber with excessive pressure • Leave the area tidy once completed Requirements • Must have your own pressure washer suitable for timber • Ability to assess appropriate pressure to avoid timber damage Fence Details • Standard residential timber fence • Weathered condition • Ground level access

I have lovely wooden panels from a bed surround and I would like them made into a free standing bed head.

After someone experienced to supply and install vertical panelling around 3 sides of laminex kitchen island bench. 2.5m (L), 87cm (H) 2 x sides of 61cm ea. Seeking cost estimate, timing as well as product and supplier/manufacturer. Preferred contact msg, text or email. Open to offers to consider Added example picture for some guidance. Looking for light colour, scandi look. Many thanks!

One of the legs of our dining table recently broke. We need a handy carpenter to either rebuild the leg, or fix the current one. Click on below dropbox link to see PDF containing images and details of the break. https://www.dropbox.com/scl/fi/yedzvkixliwfwil7o04j8/Our-dining-table.pdf?rlkey=dg6pqiic0g2pkayyxz56j8k1t&dl=0